កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

បង្កើតដោយ

Forge

15. វិច្ឆិកា 2026NO
5
0
0
0
0

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
ចាប់ផ្តើម
An hour

ការណែនាំ

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់លង្ហិនបំពង់លង្ហិន1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់តុដង្កាប់តុ
រណារកាត់ដែករណារកាត់ដែក
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់តុដង្កាប់តុ
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ដែកជូតរាងម្ជុលដែកជូតរាងម្ជុល
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សន្លឹកស្ពាន់លឿងសន្លឹកស្ពាន់លឿង1 ដុំ
ខ្សែសំណផ្សារខ្សែសំណផ្សារ1 ដុំ
ហ្វ្លុចហ្វ្លុច1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

កន្ត្រៃកាត់សន្លឹកលោហៈកន្ត្រៃកាត់សន្លឹកលោហៈ
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ដែកផ្សារដែកផ្សារ
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

សម្ភារៈសម្រាប់ជំហាននេះ៖

ខ្សែលួសដែកខ្សែលួសដែក1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

សម្ភារៈ

5

ឧបករណ៍ចាំបាច់

8

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...