កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)
Woody

បង្កើតដោយ

Woody

13. វិច្ឆិកា 2026NO
6
0
0
0
0

Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)

Stillman Taylor's skis from The Boy Mechanic, Book 3 (1919): "far easier than snowshoe construction, since each runner is made from a single piece of plank". Ash or hickory is cut to his 8 ft pattern, thinned from the top only, the tips steamed to a 6 in bend, a centre groove cut, and the skis oiled and waxed.
មធ្យម
About 1 week

ការណែនាំ

1

Fig. 5 in centimetres, and the wax

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read The Boy Mechanic, Book 3

"Either hickory or ash will give satisfaction, because both are heavy woods, as well as strong and flexible." For a man of good height, 7 to 8 ft is the right length.
3

Get and choose the wood

Get two ash or hickory planks about 9 ft long and 2 in thick, from the outside of the lower trunk, with the grain running as in his Fig. 6, A/D (in ash choose open, widely spaced grain). Or split a sound, straight tree about 10 in across and clear of knots for 10 ft: axe a straight groove about 1 in deep along each side and drive small wood wedges along it; hew only enough off the outside to make the flat running surface.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
ខ្សែវាស់ខ្សែវាស់
4

Lay out and saw

Make a paper pattern from his Fig. 5 (8 ft ski): 3-3/8 in wide at the heel, 3-1/8 in at the foot, 4 in at the bend, rounding to the toe. Trace it on the plank and saw out; on green wood make the width about 1/4 in greater for shrinkage.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ខ្មៅដៃខ្មៅដៃ
រណារដៃរណារដៃ
ខ្សែវាស់ខ្សែវាស់
5

Plane to thickness

Plane the running surface perfectly smooth, grain straight from point to heel. Work the thickness down from the top side only, never the bottom: about 1/2 in at the heel, 3/4 in at the foot and 1/2 in at the bend.

ឧបករណ៍ដែលត្រូវការ៖

កាំបិតឈូសឈើដៃកាំបិតឈូសឈើដៃ
រនាសពីរដៃរនាសពីរដៃ
6

Steam the tip

Lay the ski over a wash boiler of boiling water and soak the tip by mopping it with the water on a cloth tied to a stick. Bend gradually over many treatments to a good 6 in bend (it finishes near 5 in, as the wood straightens a little as it dries). Hold it in a rough frame over a short log, or lash or cleat the tips to the bench, as in his Fig. 7. The arch under the foot is easily put in, and easily straightened when cold if overdone.

ឧបករណ៍ដែលត្រូវការ៖

ឆ្នាំងធំឆ្នាំងធំ
អំបោសជូតឥដ្ឋអំបោសជូតឥដ្ឋ
ឈ្នាប់ដងវែងឈ្នាប់ដងវែង
7

Binding hole, balance and groove

Put in the hole for the foot binding. If the wood was left long, trim the heel so the ski balances when lifted by the toe straps (he sees no advantage in weighting a light heel with lead). Cut a groove in the exact centre of the running surface, about 1/8 in deep and 3/8 to 1/2 in wide, from the heel to the start of the bend, with a grooving plane or a small gouge.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ខ្សែស្បែកខ្សែស្បែក2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ស្វានដៃស្វានដៃ
ដែកឆូតឈើដែកឆូតឈើ
ដែកឆូតកោងដែកឆូតកោង
រណារដៃរណារដៃ
8

Finish and wax

Sandpaper top and bottom and rub down with linseed oil with a little paraffin or beeswax in it; oil and wax the running surface (spar varnish on the tops if you want gloss). For a hard wax, melt 10 oz of beeswax with 5 oz of rosin, stir in 1 oz of turpentine and pour into small boxes. Rub it on and go over it with a hot flatiron; too much wax makes climbing hard.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្រដាសខាត់ក្រដាសខាត់1 ដុំ
ប្រេងលីនស៊ីតប្រេងលីនស៊ីត1 ដុំ
ក្រមួនប៉ារ៉ាហ្វីនក្រមួនប៉ារ៉ាហ្វីន1 ដុំ
ក្រមួនឃ្មុំក្រមួនឃ្មុំ1 ដុំ
ជ័រស្រល់ (រ៉ូស៊ីន)ជ័រស្រល់ (រ៉ូស៊ីន)1 ដុំ
ប្រេងស្រល់ប្រេងស្រល់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឆ្នាំងធំឆ្នាំងធំ
ឆ្នាំងអ៊ុតដែកឆ្នាំងអ៊ុតដែក
ជក់លាបធំទូលាយជក់លាបធំទូលាយ
9

Troubleshooting

Ski troubleshooting.

Flow

Loading...
10

History and honest limits

From "How to Make Skis" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 27-30). His text gives the groove as 3/8 to 1/2 in wide; Fig. 5 shows 3/8 in. He does not describe the binding. The tools and metric figures are ours.

សម្ភារៈ

8

ឧបករណ៍ចាំបាច់

13

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...