예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere
Beaten in an open bowl, egg spatters and the air is not forced into it.
James M. Jay of Canton, Ohio, received US 27,054, dated 7 February 1860, for an egg beater whose case is a hollow globe of two halves hinged and caught together; a horizontal shaft through it carries concentric rings, the outer one close to the inside so it sweeps the bottom, turned by a wheel and gear on a stand. "The air which occupies the upper part ... is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs."
This rung works out the air-to-egg ratio, then prints the ring dasher and gears, closes it in two bowls, and times a beating.
중급
About 5 hours, plus printing
안내
1
1
Air shut in with the eggs
Air shut in with the eggs
Jupyter 노트북 불러오는 중…
2
2
A dasher in a closed box before it
A dasher in a closed box before it
The embedded blueprint spins a dasher in a square box. Jay shuts the eggs in a globe so the air is driven into them.
3
3
Read US 27,054
Read US 27,054
"In my egg beater the air which occupies the upper part of the hollow bottom B, together with that which fills the cover or cap C, is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs by the rings or dashes H', while the eggs are carried up and through the air in the cap or case C, so that a perfect mixture of the air and eggs is effected."
4
4
Print the rings and gears
Print the rings and gears
Print the concentric-ring dasher (/uploads/blueprints/closed-globe-egg-beater-rings.stl), the 36-tooth wheel (/uploads/blueprints/closed-globe-egg-beater-wheel-36.stl) and the 12-tooth gear (/uploads/blueprints/closed-globe-egg-beater-gear-12.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
이 단계의 재료:
PETG 필라멘트1 개필요한 도구:
FDM 3D 프린터5
5
Make the globe
Make the globe
Take two matching bowls 120 mm across from the set. Drill both rims at opposite points for the shaft, 5.5 mm, so the shaft lies on the joint.
이 단계의 재료:
믹싱 볼 세트1 개필요한 도구:
무선 드릴
드릴 비트 세트
디지털 캘리퍼스 6인치6
6
Shaft, rings and stand
Shaft, rings and stand
Pass a 5 mm rod through one bowl's holes and the dasher's hub, and epoxy the hub at the centre. Epoxy the 12-tooth gear on the rod outside. Mount the 36-tooth wheel with a crank on an M5 screw on a hardwood upright so it meshes, and stand the lower bowl in a plywood ring.
이 단계의 재료:
연강 환봉1 개
2액형 에폭시1 개
경목 블록1 개
합판1 개
기계 나사1 개
평와셔1 개
육각 너트1 개
#8 × 1인치 나무 나사1 개필요한 도구:
쇠톱(핵소)
실톱(코핑 소)무선 드릴드릴 비트 세트
멍키스패너
드라이버 세트7
7
The patent drawing
The patent drawing
US 27,054 drawing sheet, public domain (expired patent).
8
8
Closed against open
Closed against open
Beat two egg whites with the top bowl clamped on and time them to stiff peaks; then again with the top off. Compare the times and the volume of foam.
이 단계의 재료:
달걀4 개필요한 도구:
스톱워치
디지털 주방 저울9
9
A globe that leaks, rings that scrape
A globe that leaks, rings that scrape
Closed-globe egg beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**James M. Jay** of Canton, Ohio, assignor to himself and John Danner, received US 27,054, dated 7 February 1860. The halves are turned to break joints and fit tight; a hook on the cover hangs on a pivot between lugs, and a swinging catch holds the cover down; the shaft's bearings are in the lower half's edge, the cover cut to fit over them. He wrote that it does not matter whether one or more eggs are beaten.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Two bought bowls stand in for his turned halves, without a hinge. Your times are the result.
재료
11- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 플레이스홀더
- 4 개플레이스홀더
이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.