예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Flaring-Tub Slat-Reactor Churn: The Cream Climbs the Flare and Is Beaten Back by Slats
Grover let the shape of the tub do the work: spun cream climbs a flaring side.
Hosea H. Grover of North Cohocton, Steuben County, New York, received US 10,245, dated 15 November 1853, for a rotary churn: a crank and shaft with a transverse piece near the bottom, standing in a step at the tub's bottom, under slats across the top held by wires and a cross piece fastened with staples. Turning it "produces centrifugal motion in the milk and thereby causes it to rise up the flaring surface of the tub until it meets the reactor by which it is beat back upon the dash." The small churn is of tin; for larger quantities he made the tub of wood, less flaring, with a pinion and larger cog wheel to speed the dash.
This rung looks at how high spun cream could climb, then prints the dash bar, step, slat rails and bearing block, fits them in a flaring stainless bowl, and makes butter.
초급
About 3 hours, plus printing
안내
1
1
How high it could climb
How high it could climb
Jupyter 노트북 불러오는 중…
2
2
A reaction in the churn before it
A reaction in the churn before it
The embedded blueprint makes the cream react against oars pitched opposite ways. Grover throws it up a flaring side into fixed slats.
3
3
Read US 10,245
Read US 10,245
"These slats are designed to be placed in singly and then the wires passed through them so that the slats may be used in any required number to suit the quantity and quality (that is the thickness) of the milk or cream to be churned. Thus situated the slats constitute a reactor."
4
4
Print the parts
Print the parts
Print the dash bar b with its square socket (/uploads/blueprints/flaring-tub-slat-reactor-churn-dash-bar.stl), the step (/uploads/blueprints/flaring-tub-slat-reactor-churn-step.stl), two slat rails that hook over the rim like his staples (/uploads/blueprints/flaring-tub-slat-reactor-churn-slat-rail.stl) and the bearing block for the cross piece (/uploads/blueprints/flaring-tub-slat-reactor-churn-bearing-block.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
이 단계의 재료:
PETG 필라멘트1 개필요한 도구:
FDM 3D 프린터5
5
Dash and step
Dash and step
Stand the step in the middle of a large stainless mixing bowl with sloping sides, about 300 mm across. Cut a 10 mm square hardwood shaft to stand in it and reach 60 mm above the rim, push the dash bar onto it 15 mm above the step, and glue a pine crank arm and dowel handle on top.
이 단계의 재료:
큰 스테인리스강 믹싱볼1 개
단단한 나무 목심1 개
소나무 판재1 개
목공용 접착제1 개필요한 도구:
손톱(핸드소)
무선 드릴
드릴 비트 세트
사포6
6
Slats, wires and cross piece
Slats, wires and cross piece
Hook the two rails over the rim opposite each other. Cut hardwood laths 10 mm thick to span between the rails in their grooves, each with a 14 mm hole in its middle for the shaft, and slide in as many as the cream needs, one at a time. Push a 3 mm stainless rod down through each rail and the slat ends, as his wires. Lay a 24 by 12 mm lath across the rim through the bearing block, over the rails, as the cross piece d, the shaft through the block.
이 단계의 재료:
단단한 나무 목심1 개
연강 환봉1 개필요한 도구:
손톱(핸드소)무선 드릴드릴 비트 세트
쇠톱(핵소)7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the flaring tub cut away to show the step and the dash bar near the bottom, three slats across the top in the rails hooked over the rim, the wires, and the cross piece with its bearing block and the crank.
8
8
Spin and make butter
Spin and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Turn the crank briskly so the cream climbs the bowl's side into the slats; if it does not reach them, take out the top slat and lower the rest. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
이 단계의 재료:
생크림1500 ml
굵은 천일염1 개
물1 개필요한 도구:
꽂아 두는 프로브 온도계
스톱워치
디지털 주방 저울큰 스테인리스강 믹싱볼9
9
Cream that will not climb, a shaft that wanders
Cream that will not climb, a shaft that wanders
Flaring-tub slat-reactor churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Hosea H. Grover** of North Cohocton, Steuben County, New York, received US 10,245, dated 15 November 1853 (the drawing sheet reads "H. H. Grover"). He did not claim a conical tub with a revolving dasher, with or without breakers, as such churns had been used before; he claimed such a conical tub with a vertical revolving dasher at its bottom combined with breakers at the top.
**Honest limits.** A mixing bowl with curved sides, hardwood and printed parts stand in for his tin cone; the notebook's rise is an upper bound, not a measurement. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
재료
9- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1500 ml플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
필요 도구
10- 플레이스홀더
- 플레이스홀더
- 1 vendor sell this, none ship to you yet플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.