예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블

Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
The Hights made the wings of a horizontal box-churn dash into a screw.
Cornelius R. Hight and John Hight of Geneva, Illinois, received US 7,490, dated 9 July 1850, for a "reacting spiral revolving dash" in a box churn: a shaft with four arms, those at one end at right angles to those at the other, and two wings fastened from arm to arm "so as to produce a quarter twist in the wings as they extend along the shaft." Its revolution produces "opposite currents, in the cream"; reversed, "the butter collects at the ends of the wings."
This rung works out the wings' pitch, then prints the dash in one piece, fits it in a box, and makes butter.
중급
About 3 hours, plus printing
안내
1
1
The quarter twist
The quarter twist
Jupyter 노트북 불러오는 중…
2
2
Oblique wings on a horizontal arbor before it
Oblique wings on a horizontal arbor before it
The embedded blueprint sets straight wings at 30° to the axle. The Hights twist theirs a quarter turn from end to end, like a screw.
3
3
Read US 7,490
Read US 7,490
"The peculiar construction of the dash, consists in setting the arms to which the wings are attached, at right angles, upon opposite sides of the shaft, so as to produce a quarter twist in the wings as they extend along the shaft from one arm to the other."
4
4
Print the dash
Print the dash
Print the dash on end in one piece with supports (/uploads/blueprints/quarter-twist-spiral-dash-churn-dash.stl): shaft, four arms and two wings each twisted a quarter turn. Print the crank arm (/uploads/blueprints/quarter-twist-spiral-dash-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
이 단계의 재료:
PETG 필라멘트1 개필요한 도구:
FDM 3D 프린터5
5
Fit the box
Fit the box
Take a food-safe box about 220 × 150 × 160 mm, its proportions close to his 18 × 12 × 13 inches. Drill both ends on the axis 80 mm up. Push a 10 mm square hardwood shaft through one end, the dash and the other end, with a leather washer at each.
이 단계의 재료:
식품용 보관 용기1 개
단단한 나무 목심1 개
가죽 띠1 개필요한 도구:
무선 드릴
드릴 비트 세트
손톱(핸드소)6
6
Crank and lid
Crank and lid
Glue the crank arm and a dowel handle on the shaft's outer end, and fit the box's lid, as his rabbeted cover.
이 단계의 재료:
단단한 나무 목심1 개
목공용 접착제1 개필요한 도구:
사포7
7
The patent drawing
The patent drawing
US 7,490 drawing sheet, public domain (expired patent).

8
8
Churn, then reverse to collect
Churn, then reverse to collect
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Crank steadily; time until the butter comes. Then reverse the crank so the butter collects at the ends of the wings, as they said. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
이 단계의 재료:
생크림1500 ml
굵은 천일염1 개
물1 개필요한 도구:
꽂아 두는 프로브 온도계
스톱워치
디지털 주방 저울
큰 스테인리스강 믹싱볼9
9
Wings that scrape, butter that won't collect
Wings that scrape, butter that won't collect
Quarter-twist spiral dash troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Cornelius R. Hight and John Hight** of Geneva, Kane County, Illinois, received US 7,490, dated 9 July 1850. Their wings could be wood or tin, split into the arms with a saw and fastened with brads or small screws; the wing's inner border was cut to arcs of 16- and 23-inch circles; the dash ran on a coupling gudgeon in a cast box and a screw pivot. They wrote it made butter "in from 5 to 8 minutes"; that is their claim, not our measurement. They claimed the application of a reacting spiral revolving dash to a box churn or any of the usual forms of churns.
**Honest limits.** A food-safe box and a printed dash stand in for theirs, and our wings twist evenly rather than following their curved borders. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
재료
8- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1500 ml플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.



