ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream
Daniel Deshon 2d of Somerset, Pennsylvania, received US 27,701, dated 3 April 1860, for a churn. A box of cream stands on curved rockers whose pegs sit in notches along the ways of a stand. Rocked by a handle, the box tips end to end and the cream runs through racks of rods; as the rockers roll, the point they rest on moves along with the weight, so little force is needed.
The patent gives no sizes; every size here is ours, and so is our reading of where the racks sit.
ระดับกลาง
About 2 days
คำแนะนำ
1
1
A fulcrum that walks
A fulcrum that walks
กำลังโหลดสมุด Jupyter…
2
2
Cream rushing end to end through pins, one month before
Cream rushing end to end through pins, one month before
Newbrough's barrel tips on a fixed pivot. Deshon's box rolls, so its pivot follows the cream.
3
3
Read US 27,701
Read US 27,701
"... this is done without contending but very little with the weight from the fact that the fulcrum at the bottom of the rockers (b) changes from one end to the other in accordance to the change of the weight inside of the vessel, always keeping in the center of the weight; consequently balancing the weight in its motion and saving most of the labor required to churn."
4
4
Vessel a and lid d
Vessel a and lid d
From 20 mm hardwood board make a box 600 x 250 mm inside and 290 deep; glue and screw it and seal the inside joints with silicone sealant. Cut a 150 mm opening across the middle of the top and a lid to fit it, with a hardwood block handle e.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง3 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้40 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์แบบบาร์
ชุดไขควง
ตลับเมตร5
5
Racks i
Racks i
Make two racks, each two hardwood side bars 24 x 20 mm, 355 long, with nine 10 mm stainless rods across between them. Stand them in the vessel leaning together, their feet on the floor 30 mm from the ends, meeting in the middle 240 mm above the floor.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส2 ชิ้น
กาวไม้1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน6
6
Rockers b with projections f, and handle c
Rockers b with projections f, and handle c
Draw an arc of 400 mm radius with the compass on two 20 mm hardwood boards and cut each rocker with that arc as its bottom, 48 degrees of arc (325 mm), rising to the box's top; leave one 140 mm taller and cut a hand-hole in it as the handle c. Bore seven 12 mm holes along each arc, 6 degrees apart, and glue in dowel pegs standing 8 mm out as the projections f. Bolt a rocker on each long side of the vessel, centred, the arc's lowest point 40 mm below the vessel's bottom.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สลักเกลียวหัวกลม4 ชิ้น
น็อตปีกผีเสื้อ4 ชิ้นเครื่องมือที่ต้องใช้:
เข็มทิศ
เลื่อยจิ๊กซอว์
ไม้โปรแทรกเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
กระดาษทราย
ประแจเลื่อน7
7
Pedestal h with ways and notches g
Pedestal h with ways and notches g
Cut two hardwood ways 520 x 120 x 30 mm and set them on edge under the rockers, 290 mm apart inside; join them with two cross boards near the floor. Cut seven notches 14 mm wide and 11 deep in each way's top edge, 41.9 mm apart from the middle, to match the pegs.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้16 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์แบบบาร์
ชุดไขควง
ตลับเมตร8
8
The build in 3D
The build in 3D
FreeCAD model of this build, tipped 10 degrees and cut through the middle: the vessel with its lid and the two racks leaning together, the rockers with their pegs in the ways' notches, and the pedestal.
9
9
Churn
Churn
Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the vessel and close the lid. Push and pull the handle c steadily, tipping the vessel up to about 18 degrees each way, timing it. When the butter comes, lift the lid, take out the racks and the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด10 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่10
10
Troubleshooting
Troubleshooting
Rolling-rocker churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Daniel Deshon 2d** of Somerset, Pennsylvania, US 27,701, 3 April 1860, "Churn". He claimed the racks, vessel, pedestal and rockers with projections in notched ways, combined. He places the racks only by dotted lines in his figure; our two racks leaning together are our reading of them. Every size here is ours.
วัสดุ
11- 3 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 56 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 10 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
19- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
1พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Rocking Barrel Brake-Pin Churn: Cream Rushes End to End Through Rows of Pins, a Diagonal Board Gathers the Butter
โดย Buttercup
งานไม้
8
0
0
0
0
0

Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End
โดย Buttercup
งานไม้
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

