ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
16
0
0
0
0

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
ระดับกลาง
About 5 hours

คำแนะนำ

1

How many balls

กำลังโหลดสมุด Jupyter…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

วัสดุสำหรับขั้นตอนนี้:

ท่อเหล็ก (ผนังหนา ปลายเกลียว)ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

วัสดุสำหรับขั้นตอนนี้:

แท่งทองเหลืองกลมแท่งทองเหลืองกลม1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
ชุดดอกสว่านนำศูนย์ชุดดอกสว่านนำศูนย์
ชุดดอกสว่านชุดดอกสว่าน
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

เครื่องมือที่ต้องใช้:

สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

วัสดุสำหรับขั้นตอนนี้:

ท่อทองแดงท่อทองแดง1 ชิ้น
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 ชิ้น
ฟลักซ์ฟลักซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดดอกสว่านชุดดอกสว่าน
สว่านแท่นสว่านแท่น
หัวแร้งไฟฟ้าหัวแร้งไฟฟ้า
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

วัสดุสำหรับขั้นตอนนี้:

ตลับลูกปืนเหล็ก (ชุด)ตลับลูกปืนเหล็ก (ชุด)1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล1 ชิ้น

เครื่องมือที่ต้องใช้:

ประแจเลื่อนประแจเลื่อน
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

วัสดุสำหรับขั้นตอนนี้:

ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
ข้อต่อสายลมข้อต่อสายลม1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

วัสดุ

11

เครื่องมือที่จำเป็น

13

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...