ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
12
0
0
0
0

Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)

Marselius J. Logan of Springfield, Virginia, received US 1,377,495, dated 10 May 1921. Three knives sit in grooves along a conical head, their bevelled edges just proud of the cone. A collar screwed along the shank pushes all their back ends at once, so each cuts the same share. When they wear, a turn of the collar sets them out again. Set screws lock them. A stop pin beside them halts every countersink at the same depth. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 2 days

คำแนะนำ

1

Setting the knives out evenly

กำลังโหลดสมุด Jupyter…
2

Read US 1,377,495

"All of the cutters or knives 10 are made alike in length as well as other dimensions, so that by screwing the collar 7 into contact with the inner ends 12 of all of said cutters, the latter may be evenly adjusted to cut equally, and when their cutting edges 11 become worn down said cutters may be uniformly projected in order to provide the proper clearance."
3

Turn the inner member 1 and the sleeve 4

From 30 mm steel bar turn the inner member: a 90 degree cone 3 26 mm across at its base, a short cylindrical edge under it, and a shank 2 14 mm across, threaded M14 for 20 mm below the head 6 and plain below. From 40 mm bar turn the sleeve: a ring bored 0.03 mm under the head's edge, with a flange 5 30 mm long bored 22 mm, so it leaves an annular space 13 round the shank. Heat the sleeve to 250 C in the oven and drop it over the head's edge; let it cool.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน2 ชิ้น
น้ำมันตัดกลึงน้ำมันตัดกลึง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
ก้านคว้านรูก้านคว้านรู
มีดตัดงานกลึงมีดตัดงานกลึง
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
เตาอบเตาอบ
ถุงมืองานเชื่อมถุงมืองานเชื่อม
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
4

Grooves, knives and screws

Saw and file three grooves 4 mm square, parallel to the axis, a third of the way round from each other, through the joint of head and sleeve and on into the annular space. File the cone away 14 ahead of each groove for the shavings. Cut three knives 32 mm long from 4 mm square tool steel, exactly alike, and grind each one's top end to the cone's slope with a bevelled cutting edge 11. Harden them (cherry red, water, temper to light straw). Drill and tap M4 through the sleeve over each groove for the set screws 15. Make a collar 7 with an M14 thread to screw up the shank inside the flange, and an M4 set screw 19 to lock it. Drill and tap M5 into the head's edge behind one knife for the stop pin 16, with an M4 set screw 18 to lock it.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือสี่เหลี่ยมจัตุรัสเหล็กเครื่องมือสี่เหลี่ยมจัตุรัส1 ชิ้น
เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
สกรูหนอนปลายเว้าสกรูหนอนปลายเว้า5 ชิ้น
สกรูหัวจมหกเหลี่ยมสกรูหัวจมหกเหลี่ยม1 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เครื่องเจียรตั้งโต๊ะเครื่องเจียรตั้งโต๊ะ
เตาตีเหล็กเตาตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
แม่เหล็กเล็กแม่เหล็กเล็ก
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
หินลับมีดหินลับมีด
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับต๊าปเกลียวด้ามจับต๊าปเกลียว
เครื่องกลึงโลหะเครื่องกลึงโลหะ
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
5

Set, lock and countersink

Slide the knives into their grooves, back ends down in the annular space. Screw the collar up until all three knives' edges stand 0.3 mm out of the cone, and lock it and the knives. Set the stop pin so it touches the work when the countersink is the size wanted, and lock it. Countersink a row of screw holes in hardwood: every one should come out the same.

เครื่องมือที่ต้องใช้:

ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง
แว่นนิรภัยแว่นนิรภัย
6

Troubleshooting

Adjustable-knife countersink troubleshooting.

Flow

Loading...
7

History and honest limits

**Marselius J. Logan** of Springfield, Virginia, assignor of one-half to Laurence G. Alexander of Alexandria, Virginia, US 1,377,495, dated 10 May 1921, filed 14 February 1920. He claimed "a flange carried by the head and extending concentrically along the shank in spaced relation thereto, cutters mounted on the head and extending into the space between the same and the flange, and a collar adjustable on the shank within said flange for alining the cutters", and "an adjustable stop". He shows three knives; ours too. He gives no sizes; every size here is ours.

วัสดุ

6

เครื่องมือที่จำเป็น

26

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...