ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Multimeter: a Low-Voltage Pocket Meter on the ICL7106 Dual-Slope Converter (after Ammann, 1967)
Ed

สร้างโดย

Ed

22. พฤศจิกายน 2026FI
0
0
0
0
0

Multimeter: a Low-Voltage Pocket Meter on the ICL7106 Dual-Slope Converter (after Ammann, 1967)

A 3 1/2-digit digital multimeter for low-voltage projects: 2 V and 20 V DC, 200 mA and 2 kohm. One ICL7106 chip does the measuring by the dual-slope method Stephan Ammann patented in 1967: it integrates the input for a fixed time, then times how long a reference takes to bring it back to zero. Built on perfboard in a printed case. Never for mains.
ระดับกลาง
About 1 day

คำแนะนำ

1

The dual-slope method

US 3,316,547 (Ammann, Fairchild, 1967): integrate the input over a fixed time, then integrate a reference of opposite sign until the integrator is back where it started. The time that takes, counted in clock pulses, is the ratio of input to reference, so the clock and the capacitor's exact values cancel out. The ICL7106 does this on one chip and drives the LCD directly.
2

Clock, ranges and the ohms circuit

กำลังโหลดสมุด Jupyter…
3

Print the wiring sheet

Pin by pin, the base circuit (datasheet Fig. 1 values) and the range switch table.
ไฟล์แบบPDFCC0 - Free
ขั้นตอนที่ 3 - Image 1
4

Print the case

Floor down, no supports, PETG. Four holes in the top end for the leads.
ไฟล์แบบSTLCC0 - Free

วัสดุสำหรับขั้นตอนนี้:

เส้นใย PETGเส้นใย PETG60 ก.

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
5

Print the lid

Flat, no supports. Trim the LCD window to your display; the two round holes take the range switch and the toggle switch.
ไฟล์แบบSTLCC0 - Free

วัสดุสำหรับขั้นตอนนี้:

เส้นใย PETGเส้นใย PETG30 ก.

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
6

Change the case (optional)

The FreeCAD script that made the case: OUT=. freecadcmd build_all.py
build_all.pypython
"""Batch 2530 -- printed case for the ICL7106 pocket multimeter. ALL sizes ours. PETG, no supports.
  dmm-base  tray 120 x 75 x 30 mm, 4 lead exits (5 mm) in the top end wall, 4 corner posts (2.8 mm pilots for M3)
  dmm-lid   2.5 mm lid: LCD window 46 x 18 mm (trim to your LCD), 10 mm hole for the rotary switch bushing,
            16.5 mm hole for the toggle switch neck (batch 2526, M16 x 1.5), 4 x 3.4 mm screw holes
Run: OUT=<dir> freecadcmd build_all.py"""
import os
import FreeCAD as App, Part, MeshPart
OUT = os.environ["OUT"]; V = App.Vector
L, W, H, WALL, FLOOR, LID = 120.0, 75.0, 30.0, 2.4, 2.4, 2.5
def save(sh, n):
    sh = sh.removeSplitter(); bb = sh.BoundBox
    print(n, "valid", sh.isValid(), "solids", len(sh.Solids), "bbox", [round(v, 1) for v in (bb.XLength, bb.YLength, bb.ZLength)])
    if not os.environ.get("NOSAVE"):
        MeshPart.meshFromShape(Shape=sh, LinearDeflection=0.03, AngularDeflection=0.12).write(os.path.join(OUT, n + ".stl"))
    return sh
POSTS = [(WALL + 4.5, WALL + 4.5), (L - WALL - 4.5, WALL + 4.5), (WALL + 4.5, W - WALL - 4.5), (L - WALL - 4.5, W - WALL - 4.5)]
base = Part.makeBox(L, W, H).cut(Part.makeBox(L - 2 * WALL, W - 2 * WALL, H, V(WALL, WALL, FLOOR)))
for x, y in POSTS:
    base = base.fuse(Part.makeCylinder(4.0, H - FLOOR, V(x, y, FLOOR))).cut(Part.makeCylinder(1.4, 16, V(x, y, H - 15)))
for i, x in enumerate((30, 50, 70, 90)):           # COM, V, mA, ohm leads out of the top end wall (y = W)
    base = base.cut(Part.makeCylinder(2.5, WALL + 2, V(x, W - WALL - 1, H - 10), V(0, 1, 0)))
base = save(base, "dmm-base")
lid = Part.makeBox(L, W, LID, V(0, 0, H))
lid = lid.cut(Part.makeBox(46, 18, LID + 2, V((L - 46) / 2, W - 30, H - 1)))                 # LCD window
lid = lid.cut(Part.makeCylinder(5.0, LID + 2, V(L / 2, 26, H - 1)))                          # rotary switch bushing
lid = lid.cut(Part.makeCylinder(8.25, LID + 2, V(L - 22, 22, H - 1)))                        # toggle switch neck
for x, y in POSTS:
    lid = lid.cut(Part.makeCylinder(1.7, LID + 2, V(x, y, H - 1)))
lid = save(lid, "dmm-lid")

เครื่องมือที่ต้องใช้:

เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
7

Build the converter

On perfboard, wire the ICL7106 as the sheet's first table: oscillator 100 kohm and 100 pF; reference 24 kohm and the 1 kohm trimmer; 0.1 uF reference capacitor; 47 kohm, 0.47 uF and 0.22 uF (polypropylene) to node X; 1 Mohm and 0.02 uF at IN HI. Connect the LCD segments and backplane by your LCD's pinout.

วัสดุสำหรับขั้นตอนนี้:

วงจรรวมวงจรรวม1 piece (ICL7106, 40-pin DIP)
จอแอลซีดีแบบเซกเมนต์จอแอลซีดีแบบเซกเมนต์1 piece (3 1/2-digit, static drive)
แผ่นวงจรอเนกประสงค์แผ่นวงจรอเนกประสงค์1 ชิ้น
ชุดตัวต้านทานความเที่ยงสูงชุดตัวต้านทานความเที่ยงสูง8 piece (1 %: 24k, 47k, 100k, 1M, 22k, 1k and the divider below)
ชุดตัวเก็บประจุชุดตัวเก็บประจุ5 piece (0.1, 0.47, 0.22 polypropylene, 0.02 uF, 100 pF)
โพเทนชิออมิเตอร์โพเทนชิออมิเตอร์1 piece (1 kohm trimmer)
ลวดตะกั่วบัดกรีลวดตะกั่วบัดกรี5 ก.

เครื่องมือที่ต้องใช้:

หัวแร้งบัดกรีหัวแร้งบัดกรี
8

Wire the ranges

Divider from the V lead to COMMON: 4.7 M + 4.3 M, then 820 k + 82 k, then 100 k (2 V tap between the 4.3 M and the 820 k; 20 V tap between the 82 k and the 100 k). Shunt: mA lead, 250 mA fuse, 1 ohm 1 % to COMMON. Ohms: V+, 22 kohm, 1 kohm Rref, ohm lead. Wire the 3-pole 4-position switch as the sheet's second table; power through the toggle switch.

วัสดุสำหรับขั้นตอนนี้:

ชุดตัวต้านทานความเที่ยงสูงชุดตัวต้านทานความเที่ยงสูง6 piece (1 %: 4.7M, 4.3M, 820k, 82k, 100k)
ชุดตัวต้านทานชุดตัวต้านทาน1 piece (1 ohm, 0.5 W)
สวิตช์หมุนสวิตช์หมุน1 piece (3 pole, 4 position)
สวิตช์โยกสวิตช์โยก1 ชิ้น
ฟิวส์ฟิวส์1 piece (250 mA)
ที่ยึดฟิวส์ไฟกระแสตรงที่ยึดฟิวส์ไฟกระแสตรง1 ชิ้น
แบตเตอรี่แบตเตอรี่1 piece (9 V)
สายไฟต่อวงจรสายไฟต่อวงจร1 m

เครื่องมือที่ต้องใช้:

หัวแร้งบัดกรีหัวแร้งบัดกรี
คีมปอกสายไฟคีมปอกสายไฟ
9

Fit it in the case

Put the four leads (COM black; V, mA and ohm red) through their holes and knot them inside. Fix the board and battery with tape, the switches in the lid. Close with 4 x M3 x 10.

วัสดุสำหรับขั้นตอนนี้:

สายทดสอบปากคีบจระเข้สายทดสอบปากคีบจระเข้4 ชิ้น
เทปกาวสองหน้าเทปกาวสองหน้า0.2 m
สกรูหัวจมหกเหลี่ยมสกรูหัวจมหกเหลี่ยม4 piece (M3 x 10)

เครื่องมือที่ต้องใช้:

ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
10

Calibrate

On the 2 V range, measure a steady voltage (a 1.5 V cell) with a good meter and with this one; turn the trimmer until they agree. Check the other ranges against the good meter.

เครื่องมือที่ต้องใช้:

มัลติมิเตอร์ดิจิทัลเกรดห้องปฏิบัติการมัลติมิเตอร์ดิจิทัลเกรดห้องปฏิบัติการ
11

Troubleshooting

Meter problems and fixes.

Flow

Loading...
12

History and honest limits

Stephan K. Ammann, assignor to Fairchild: US 3,316,547, "Integrating Analog-to-Digital Converter", filed 15 July 1964, granted 25 April 1967. Chip values from the Intersil ICL7106 datasheet. Ours: the ranges, the divider, the shunt, the ohms circuit and the case. Low voltage only: up to 20 V DC and 200 mA; never on mains. Accuracy depends on your resistors (1 %) and calibration. Not built by us yet.

วัสดุ

18

เครื่องมือที่จำเป็น

6

ไฟล์ออกแบบ

3

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...