ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Reverberatory Furnace: the Air Furnace for Melting Cast Iron (Bolland, 1893)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
15
0
0
0
0

Reverberatory Furnace: the Air Furnace for Melting Cast Iron (Bolland, 1893)

An air furnace melts iron apart from the fuel: coal burns on a grate at one end, and the flame is thrown down from a low arched roof onto the iron on the bed, then leaves by a tall chimney. The iron stays cleaner than in a cupola, so founders used it for guns, rolls, heavy scrap and lumps too big for the cupola. This furnace is 30 ft 6 in long and 7 ft wide outside, 5 ft wide inside, cased in bolted wrought-iron plates. Source: S. Bolland, The Iron Founder Supplement (1893), pp. 55-67. Unknown: brick sizes, plate thickness. Picture: Fig. 14 of the book.
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Lay the foundation

Build the foundation solid of common material up to the firebrick, shaped so the firebrick bed slopes down from the chimney end to the reservoir. Keep the bricks from B to C 6 in below the finished bottom, to leave room for the sand bed.

วัสดุสำหรับขั้นตอนนี้:

อิฐอิฐ1 foundation

เครื่องมือที่ต้องใช้:

เกรียงก่อเกรียงก่อ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Build the fireplace, bridge and roof

Build the fireplace the full width of the furnace (5 ft inside, grate 5 ft long). Set the bridge wall at least 2 ft 3 in from the face of the grate bars. Build bridge, sides, roof and fireplace of the most refractory firebrick. Arch the roof the whole length, low, so it throws the flame down onto the bed; fill above the arches with common material. Leave the side charging hole (5 x 4 ft), the top hole (furnace width x 6 ft), the puddling hole over the reservoir, a sight hole and the tap hole.

วัสดุสำหรับขั้นตอนนี้:

อิฐดินทนไฟอิฐดินทนไฟ1 lining, bridge, roof
ปูนก่อดินทนไฟปูนก่อดินทนไฟ1 setting
อิฐอิฐ1 filling above the arch
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 grate bars

เครื่องมือที่ต้องใช้:

เกรียงก่อเกรียงก่อ
3

Case it in plates and bolt it

Case the whole structure in wrought-iron plates, held at the corners with angle-irons. Run eight chief anchor bolts from side to side, clear of all working parts. Join everything with bolts, not rivets, so any plate can come off for repairs. Line the charging doors with firebrick.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กแผ่นเหล็ก1 casing, doors
เส้นเหล็กดัดเส้นเหล็กดัด8 anchor bolts
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 angle-irons, door frames
อิฐดินทนไฟอิฐดินทนไฟ1 door linings

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
4

Build the chimney

Build the chimney square, 30 to 40 ft high, with an inside course of firebrick (Fig. 14: 2 ft 6 in square inside). Make its area a little larger than the fireplace. Put a damper on top that can be worked from the bottom: it alone sets the draught. It can stand apart on a sole plate on four columns.

วัสดุสำหรับขั้นตอนนี้:

อิฐดินทนไฟอิฐดินทนไฟ1 inside course
อิฐอิฐ1 chimney
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 damper

เครื่องมือที่ต้องใช้:

เกรียงก่อเกรียงก่อ
5

Make the sand bottom

Make the bottom from B round the reservoir to C with 8 parts fire-sand to 1 of clay and 1 of ground coke. Fire it well for one to two hours before the first charge; it should last ten heats. Fill the tap hole with fire-sand and a little coal dust, which will not cake when hot.

วัสดุสำหรับขั้นตอนนี้:

ทรายทราย8 parts
ดินเหนียวดินเหนียว1 part
ถ่านโค้กโลหการถ่านโค้กโลหการ1 part, ground

เครื่องมือที่ต้องใช้:

ถ่านหินบิทูมินัสถ่านหินบิทูมินัส
6

Charge and melt

Fire with soft, non-caking bituminous coal and keep a full grate; clinker quickly and leave no holes for cold air. Charge all the iron at the start: first layer of pigs lengthwise and a little apart, next layers across, open so the flame passes. Set heavy pieces on firebricks so the flame plays all round them. Through the puddling hole, dip test pieces and skim the iron clean. To blend two grades, thrust green saplings into the melt. Close the damper before tapping. Look the furnace over after every heat.

เครื่องมือที่ต้องใช้:

ถ่านหินบิทูมินัสถ่านหินบิทูมินัส
แท่งเหล็กดิบแท่งเหล็กดิบ
ลำต้นไม้เนื้อแข็งขนาดเล็กลำต้นไม้เนื้อแข็งขนาดเล็ก
กระชอนเจาะรูกระชอนเจาะรู

วัสดุ

9

เครื่องมือที่จำเป็น

6

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...