ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Steel Skelp: Ingot to Bloom to Continuous Skelp Mill (National Tube Co., 1921)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
9
0
0
1
0

Steel Skelp: Ingot to Bloom to Continuous Skelp Mill (National Tube Co., 1921)

Skelp, the steel strip that welded pipe is made from, as National Tube rolled it in 1921: steel ingots are soaked to an even heat, rolled into blooms and sheared hot to length, then reheated and rolled in a continuous mill into long strips sized for one pipe each. For butt-weld pipe the edges are bevelled slightly and one end is trimmed to a point so the welding tongs can start it through the bell. Unknown: the skelp sizes for each pipe; the 'Spellerizing' roll treatment is named but not described. Source: National Tube Co., "National" Modern Welded Pipe (1921), pp. 38-40. Picture: the continuous skelp mill.
ขั้นสูง
Unknown

คำแนะนำ

1

Soak the ingots

Strip the moulds from the ingots while they are still hot, then set them in a soaking pit and heat them evenly right through to rolling heat. Lift them out with large tongs.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าแท่งเหล็กกล้า1 ชิ้น

เครื่องมือที่ต้องใช้:

หลุมอบแท่งเหล็กหลุมอบแท่งเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
2

Roll into blooms

Roll each ingot out longer in the bloom mill, then shear it hot into blooms or slabs of the size the pipe needs.

เครื่องมือที่ต้องใช้:

เครื่องรีดโลหะเครื่องรีดโลหะ
3

Roll the skelp

Reheat the blooms and roll them into long strips (skelp). In a continuous mill each bloom passes through several sets of rolls in one direction and comes out as finished skelp. Set the rolls to the length, width and thickness worked out for each size of pipe.

วัสดุสำหรับขั้นตอนนี้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องรีดโลหะเครื่องรีดโลหะ
4

Finish for butt welding

Bevel the edges slightly, so the strip butts truly when it is drawn through the welding die. Trim one end of each piece roughly to a point and press it to shape, so the welding tongs can start it through the bell.

เครื่องมือที่ต้องใช้:

เครื่องรีดโลหะเครื่องรีดโลหะ
กรรไกรตัดแผ่นเหล็กกรรไกรตัดแผ่นเหล็ก

วัสดุ

2

เครื่องมือที่จำเป็น

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...