ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
9
0
0
0
0

Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket

Clark Wright and William Phelps of Sycamore, Illinois, received US 28,802, dated 19 June 1860, for a churn. The tub itself spins, carried on a plate that rests on a crank-turned friction wheel. The cream climbs the side until a flange stops it, where a fixed spout catches it and shoots it into a perforated basket hung loose in the middle; the butter collects in the basket while the milk runs out through its holes and climbs again. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 2 days, plus printing

คำแนะนำ

1

How fast the tub must turn for the cream to climb

กำลังโหลดสมุด Jupyter…
2

Cream flung outward and jetted, three months before

Sangster spins paddles to fling the cream. Wright and Phelps spin the whole tub.
3

Read US 28,802

"A quantity of cream being placed in the tub F, and the latter rapidly rotated by means of the crank D and friction wheel E, the cream ascends the sides of the tub by centrifugal force until arrested by the flange f and being caught by the spout K is deflected inward and projected in a forcible and continuous stream into the basket H, causing violent agitation in the body of cream as well as friction as it flows out through the apertures in the basket."
4

Print the basket H

Perforated cone basket 160 mm across at the top, 130 at the bottom, 150 tall, with a hub bored 12.6 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the spout K

Curved spout 40 mm wide, its mouth at the wall turning inward over 55 mm, with a hanger and a clamp that slides along the bar I. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Base A, standard B, spindle G and plate g

Make a hardwood base 520 x 560 mm. Screw a hardwood standard 60 mm square in its middle, its top bored 16.6 mm to take a 16 mm stainless spindle. Cut a plywood disk plate 300 mm across, fix the spindle in its centre, and screw the bucket down on it, sealing the screw heads inside with silicone. Screw a ring of HDPE sheet, 26 mm wide, inside the bucket 340 mm up as the flange f, and a hardwood socket bored 12.6 mm in the floor's centre.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้16 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
7

Friction wheel E, shaft C and crank D

Turn a hardwood wheel E 220 mm across with its rim rounded in section, as the patent's "regular convexity". Bolt two hardwood bearing blocks to the base so a 16 mm stainless shaft C runs straight out from under the spindle, at a height where the wheel, fixed on its inner end 50 mm from the spindle, just carries the plate. The shaft must point at the spindle, so the wheel rolls on the plate without scrubbing. Fix the wheel on the shaft, and a hardwood crank D with a dowel handle on its end; hold it with collars.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม4 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ4 ชิ้น
Shaft CollarShaft Collar2 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงไม้เครื่องกลึงไม้
กระดาษทรายกระดาษทราย
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ประแจเลื่อนประแจเลื่อน
8

Standards J, bar I, pin, basket H and spout K

Stand two hardwood standards J 30 x 30 mm either side of the bucket and join their tops with a bar I across it, bored 12.6 mm over the centre. Drop a 12 mm stainless pin through the bar into the floor socket and slide the basket onto it so it turns freely. Clip the spout's clamp on the bar so its mouth sits just under the flange, close to the wall, facing against the tub's turn; slide it in or out to suit.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
สกรูไม้สกรูไม้6 ชิ้น
กาวไม้กาวไม้1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตลับเมตรตลับเมตร
9

The build in 3D

FreeCAD model of this build, the tub cut open: the spindle and plate on the friction wheel and crank, the flange, the basket on its pin, the spout hanging from the bar, and the standards.
ไฟล์แบบBLENDCC0 - Free
10

Churn

Pour about 5 litres of heavy cream at about 15 °C, checked with the thermometer, into the tub around the basket. Turn the crank briskly, timing it, until the cream climbs to the flange and runs from the spout into the basket. Keep on until the butter has gathered in the basket. Lift out the pin and basket with the butter, pour off the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด5 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
11

Troubleshooting

Rotary-tub churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Clark Wright** and **William Phelps** of Sycamore, DeKalb County, Illinois, US 28,802, 19 June 1860, "Churn". They claimed the rotary tub, stationary spout and basket together. Their wheel and plate meet as two crossed discs, the wheel's rounded rim avoiding both side thrust and broad rubbing faces. Every size here is ours.

วัสดุ

17

เครื่องมือที่จำเป็น

17

ไฟล์ออกแบบ

3

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...