УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
НОГООН ИРЭЭДҮЙ
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Controlling a DC Motor with an L298N Driver
Ed

Зохиогч

Ed

13. Долдугаар сар 2026FI
2
0
0
0
0

Controlling a DC Motor with an L298N Driver

An Arduino pin can't power a motor directly — it can't supply enough current, and it can't reverse the flow. An L298N H-bridge solves both: the Arduino sends low-power control signals, and the driver switches the motor's own battery to run it forwards, backwards and at any speed. This is the core building block of every wheeled robot.

Дунд шат
1-2 hours

Зааварчилгаа

1

Wire the driver, motor and battery

Push the L298N's control header into the breadboard. From the Arduino, jumper pin 8 to IN1, pin 9 to IN2, and pin 10 to ENA. Connect the DC motor's two wires to the OUT1/OUT2 screw terminals, and a 4×AA battery pack to the +12V and GND motor terminals. IMPORTANT: join all the grounds together — Arduino GND, driver GND and battery GND — or the motor won't run.

Materials for this step:

Arduino Uno R3 SMDArduino Uno R3 SMD1 ширхэг
Full-Bridge Motor Driver Dual - L298NFull-Bridge Motor Driver Dual - L298N1 ширхэг
Hobby Motor - GearHobby Motor - Gear1 ширхэг
Battery Holder - 4xAA Square TerminatedBattery Holder - 4xAA Square Terminated1 ширхэг
Breadboard - ClassicBreadboard - Classic1 ширхэг
Jumper Wires Premium M/M 20 AWG - 15.5 cmJumper Wires Premium M/M 20 AWG - 15.5 cm1 баглаа
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port. Leave the motor battery switched off until the code is uploaded.

Materials for this step:

SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 ширхэг

Tools needed:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the motor sketch

Paste this sketch and upload, then switch on the battery. The motor runs forward, stops, reverses, and stops — on a loop.

dc_motor_l298n.inoarduino
// Control a DC motor's speed and direction with an L298N H-bridge.
// L298N IN1 -> pin 8, IN2 -> pin 9, ENA (PWM speed) -> pin 10.
// The motor is powered by the battery pack through the driver; all grounds are joined.

const int IN1 = 8;
const int IN2 = 9;
const int ENA = 10;   // PWM speed pin (0-255)

void setup() {
  pinMode(IN1, OUTPUT);
  pinMode(IN2, OUTPUT);
  pinMode(ENA, OUTPUT);
}

void loop() {
  // forward at medium speed
  digitalWrite(IN1, HIGH);
  digitalWrite(IN2, LOW);
  analogWrite(ENA, 180);
  delay(2000);

  // stop
  analogWrite(ENA, 0);
  delay(1000);

  // reverse at full speed
  digitalWrite(IN1, LOW);
  digitalWrite(IN2, HIGH);
  analogWrite(ENA, 255);
  delay(2000);

  // stop
  analogWrite(ENA, 0);
  delay(1000);
}
4

Test and control it

Watch the motor go forward, stop, reverse. IN1/IN2 set the direction (swap which is HIGH to flip it); the number in analogWrite(ENA, ...) sets the speed from 0 (off) to 255 (full). If the motor doesn't spin, check that all three grounds are joined and the battery is on.

5

Make it a robot

The L298N drives TWO motors. Wire a second motor to OUT3/OUT4 and control it with IN3, IN4 and ENB on three more Arduino pins. Two motors on a chassis with wheels gives you a robot base you can drive — turn by running the wheels at different speeds or directions.

Материал

7

Шаардлагатай багаж

1
Estimated Total
$60.00

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

Blinking LED — Your First Arduino ProjectAdmiral OOM зохиосон
Driving a Motor — SIK Circuit 12Ed зохиосон

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Controlling a Stepper Motor with an EasyDriverelectronics
Blinking an LED with LilyPad Arduinoelectronics
Making a Motion-Reactive LilyPad Patchelectronics
Making a Color-Changing LilyPad Patchelectronics
Building a Carbon Monoxide Detectorelectronics
Building an Air-Quality Monitorelectronics

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Loading comments...