IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Àwọn Ìtọ́nisọ́nàIṢẸ́ ỌWỌ́
IṢẸ́ ỌWỌ́
Ìtọ́nisọ́nà 1,675 wà • Ẹ̀ka kékeré 11
Ṣàwárí Àwọn Ẹ̀ka Kékeré
Àwọn Ìtọ́nisọ́nà (1,675)
Wax and Rubbing Out: The Last Step That Makes It Feel Right
láti ọwọ́ Woody
Iṣẹ́ Igi
39
0
0
0
0
0
Varnish and Polyurethane: Thin Coats, and Leave It Alone
láti ọwọ́ Woody
Iṣẹ́ Igi
42
0
0
0
0
0
Stain: Colour Goes In Unevenly Unless You Make It Behave
láti ọwọ́ Mary
Àwọn Ohun Èlò
37
0
0
0
0
0
Preparing the Surface: Every Flaw Gets More Visible, Not Less
láti ọwọ́ Woody
Iṣẹ́ Igi
39
0
0
0
0
0
Oil Finishes: Wipe On, Wipe Off, and the Rag That Can Catch Fire
láti ọwọ́ Mary
Àwọn Ohun Èlò
30
0
0
0
0
0
Runs, Nibs, Cloudiness and Fisheye: Fixing a Finish That Went Wrong
láti ọwọ́ Woody
Iṣẹ́ Igi
42
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
41
0
0
0
0
0
What a Glue Joint Is: Why a Good One Breaks Everywhere Except the Glue
láti ọwọ́ Woody
Iṣẹ́ Igi
46
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All
láti ọwọ́ Woody
Iṣẹ́ Igi
43
0
0
0
0
0
Surface Preparation: The Part That Decides Whether It Holds
láti ọwọ́ Woody
Iṣẹ́ Igi
40
0
0
0
0
0
Re-Gluing a Joint That Came Apart: You Must Get the Old Glue Off
láti ọwọ́ Woody
Iṣẹ́ Igi
49
0
0
0
0
0
Squeeze-Out, Starvation and Reading a Joint That Failed
láti ọwọ́ Mary
Àwọn Ohun Èlò
51
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much
láti ọwọ́ Woody
Iṣẹ́ Igi
53
0
0
0
0
0
Choosing the Adhesive: Open Time, Gap Fill, and What It Has to Survive
láti ọwọ́ Mary
Àwọn Ohun Èlò
40
0
0
0
0
0
Stripping Insulation Without Nicking the Copper
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
45
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
50
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
50
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
52
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
45
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
31
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
51
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
52
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
44
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
46
0
0
0
0
0
Ń fi 24 nínú 1675 hàn