IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Ìmọ̀ Ẹ̀rọ
Ìtọ́nisọ́nà 578 wà • Ẹ̀ka kékeré 8
Ṣàwárí Àwọn Ẹ̀ka Kékeré
Àwọn Ìtọ́nisọ́nà (578)
Stiffness Out of Shape: Corrugating, Beading and the Turned Edge
láti ọwọ́ Emma
Ìmọ̀-ẹ̀rọ
36
0
0
0
0
0
Hitting a Bolt Instead of Leaning on It
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
30
0
0
0
0
0
The Saw That Moves Over the Work: One Pivot, Every Angle
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
28
0
0
0
0
0
Extension and Torsion Springs: Initial Tension, Hooks and Handedness
láti ọwọ́ Emma
Ìmọ̀-ẹ̀rọ
32
0
0
0
0
0
Reading a Broken Spring: Where It Broke Names the Cause
láti ọwọ́ Emma
Ìmọ̀-ẹ̀rọ
33
0
0
0
0
0
Sizing a Compression Spring: From a Requirement to Three Numbers
láti ọwọ́ Emma
Ìmọ̀-ẹ̀rọ
24
0
0
0
0
0
Buckling and Guiding: Why a Long Spring Flicks Sideways
láti ọwọ́ Emma
Ìmọ̀-ẹ̀rọ
37
0
0
0
0
0
Spring Rate: The One Number a Spring Is
láti ọwọ́ Emma
Ìmọ̀-ẹ̀rọ
33
0
0
0
0
0
Reading a Worn Tooth: What the Damage Is Telling You
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
36
0
0
0
0
0
Mounting and Alignment: Runout, Misalignment and the Contact Pattern
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
33
0
0
0
0
0
Choosing a Gear Type: Spur, Helical, Bevel, Worm or Rack
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
47
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
40
0
0
0
0
0
Centre Distance and Backlash: The Gap That Has to Be There
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
37
0
0
0
0
0
The Involute: Why Gear Teeth Are That Shape and No Other
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
45
0
0
0
0
0
Tooth Count and Ratio: One Extra Tooth Changes Everything
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
42
0
0
0
0
0
Module and Pitch: The One Number Two Gears Must Share
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
32
0
0
0
0
0
The Fuse Protects the Wire, Not the Thing You Plugged In
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
29
0
0
0
0
0
The Crimp: A Good One Is a Cold Weld, Not a Squeeze
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
36
0
0
0
0
0
Strain Relief and Routing: Wires Fail Where They Are Held
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
24
0
0
0
0
0
Choosing a Connector: What Has to Come Apart, and What Must Not
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
28
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
31
0
0
0
0
0
What a Screw Thread Is: A Ramp Wrapped Round a Cylinder
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
42
0
0
0
0
0
Tightening: How Tight Is Right, and Making It Stay
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
29
0
0
0
0
0
Tapping a Hole by Hand: The Drill Size Decides Everything
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
32
0
0
0
0
0
Ń fi 24 nínú 578 hàn