IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Self-Folding Blade Dasher Churn: Six Blades to Churn, Reverse and They Fold to Two That Gather
Robert W. Davis let the cream set the dasher and the butter fold it.
Robert W. Davis of Rodgersville, Steuben County, New York, received US 10,566, dated 28 February 1854, for "Churns for Making and Working Butter": a dasher of two end pieces B carrying blades a, and divided end pieces C hung loosely on pins "set eccentric to the axis of the dasher," carrying blades b and scroll-curved blades c. Turned one way, the cream's resistance opens it "so as to present six centripetal cutting or agitating blades"; reversed after the butter comes, the butter's resistance closes it "so as to present but two centrifugal gathering blades," which gather the butter, work it into rolls and expel the buttermilk.
This rung works out the strokes and the turning moment, then prints the end pieces, sections and blades, builds the round-bottomed churn, and makes and works butter.
Ilọsíwájú
About 5 hours, plus printing
Ìlànà
1
1
Six blades or two
Six blades or two
Ń ṣí ìwé Jupyter…
2
2
A dasher that changes when reversed, before it
A dasher that changes when reversed, before it
The embedded blueprint's floats fall back onto rollers when the crank is reversed. Davis's sections fold six blades into two S-shaped gatherers.
3
3
Read US 10,566
Read US 10,566
"The blades, c, c, have a greater curvature given them in line of a scroll, than those, b, b, as seen in the drawing. This increased curvature commences from the termination of the curve of the blades, b, b, as seen in the drawing. This increased curvature prevents the dasher throwing the butter toward the center of the churn, while gathering and working it."
4
4
Print the parts
Print the parts
Print two end pieces B (/uploads/blueprints/self-folding-blade-dasher-churn-end-piece.stl), four sections C (/uploads/blueprints/self-folding-blade-dasher-churn-section.stl), four outer blades for a and b (/uploads/blueprints/self-folding-blade-dasher-churn-outer-blade.stl) and two scroll blades c (/uploads/blueprints/self-folding-blade-dasher-churn-scroll-blade.stl). Print the blades on their lug ends. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okùn PETG1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìtẹ̀ 3D oníwàyà (FDM)5
5
The round-bottomed churn
The round-bottomed churn
Lay a round food-grade container about 180 mm across and 180 mm long on its side in a pine cradle and cut a lid opening in its top. Drill both ends on the axis for a 10 mm square hardwood shaft and fit a crank arm and dowel handle outside.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Àgọ́ ìtọ́jú ti ìpele oúnjẹ1 ẹyọ
Pákó igi pine1 ẹyọ
Àwọn dowel igi líle1 ẹyọ
Ìsúrù igi #8 x 1"1 ẹyọ
Ìdìpọ̀ Igi1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Kópìngì
Ẹ̀rọ Ìlùkòkò Aláìlókùn
Àkójọ Orí Ìlùkòkò
Ayùn Ọwọ́6
6
Assemble the folding dasher
Assemble the folding dasher
Slide the two end pieces onto the shaft inside the churn and screw an outer blade a across each pair of ends. On each side, hang a section on each end piece's pin hole with a 4 mm stainless pin, then screw an outer blade b across the sections' outer ends and a scroll blade c across their inner ends. Fit a short pin in each end piece as a stop so the sections open about square to B and fold back flat against it.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ọ̀pá Róbótó Irin Rírọ̀1 ẹyọ
Skurú ẹ̀rọ1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Irin
Ìṣù àwọn ohun ìyí skurúẸ̀rọ Ìlùkòkò Aláìlókùn7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the round-bottomed churn cut open, the end pieces with blades a on the square shaft, and the sections swung open across them on their pins, as for churning.
8
8
Churn one way, gather the other
Churn one way, gather the other
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Turn the crank the way that opens the sections and time until the butter comes. Draw off the buttermilk, then reverse the crank so the sections fold and the two S-blades gather and roll the butter. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ọ̀rá wàrà tó nípọn1500 ml
Iyọ̀ Òkun Rúkèrúdò1 ẹyọ
Omi1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìwọ̀n ooru oníhun tí ó dúró sí inú
Aago Ìdúró
Òṣùwọ̀n Díjítà Ilé Ìdáná
Àwo ìdàpọ̀ ńlá ti irin tí kò ń yá9
9
Sections that will not swing
Sections that will not swing
Self-folding blade dasher troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Robert W. Davis** of Rodgersville, Steuben County, New York, received US 10,566, dated 28 February 1854. He divided the end pieces C diagonally "in the line of a cima reversa" so the blades' edges always meet them as they open and close; his Fig. 2 showed the open position in red lines, which do not survive in the black-and-white scan. He claimed dividing the end pieces C, eccentric to the dasher's axis, combined with the blades a, b, c, so the dasher adjusts itself by the resistance of the cream and then, reversed, of the butter.
**Honest limits.** A container, printed parts and stop pins stand in for his churn and diagonal joints; he gave no sizes, and our blade curves are read from his figures. The notebook's force is illustrative. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Àwọn ohun-èlò
11- 1 ẹyọÀyè
- Àyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- Àyè
- 1 ẹyọÀyè
- 1500 mlÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
Àwọn irinṣẹ́ tó nílò
11- Àyè
- 1 vendor sell this, none ship to you yetÀyè
- Àyè
- Àyè
- Àyè
Àwọn fáìlì àpẹrẹ
1Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
Roller-and-Float Gathering Churn: Floats That Fold Onto Rollers to Press the Butter
láti ọwọ́ Woody
Iṣẹ́ Igi
35
0
0
0
0
0
Folding-Float V-Bottom Churn: Floats That Close Into a V on the Down-Stroke
láti ọwọ́ Woody
Iṣẹ́ Igi
23
0
0
0
0
0
Post-and-Float Butter-Working Churn: Floats Revolving Astride Fixed Posts
láti ọwọ́ Woody
Iṣẹ́ Igi
24
0
0
0
0
0
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.