कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Brass Sheet, Strip and Rod from an Ingot
Forge

सिर्जनाकर्ता

Forge

11. अक्टोबर 2026NO
३५
०
०
०
०

Brass Sheet, Strip and Rod from an Ingot

Brass from the alloying blueprint is cast into bars, then worked cold like copper: rolled or hammered for sheet and strip, drawn for rod. It work-hardens faster than copper, so it is annealed often, to a dull red, and can be quenched. Molten brass gives off white zinc-oxide smoke: melt it outdoors with the wind behind you.
मध्यम
A day

निर्देशनहरू

1

The brass

Making the brass ingot.
2

Cast bars

Outdoors, melt brass pieces in a crucible in the charcoal forge and pour them into a warmed, dry ingot mould: flat bars for sheet and strip, square bars for rod.

यस चरणका सामग्री:

पित्तलको ढिक्कापित्तलको ढिक्का1 केजी
कोइलाकोइला5 केजी

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
आगो सहने माटोको मुसाआगो सहने माटोको मुसा
मुसाको चिम्टामुसाको चिम्टा
पिण्डको साँचोपिण्डको साँचो
छालाको एप्रनछालाको एप्रन
वेल्डिङका पन्जावेल्डिङका पन्जा
सुरक्षा चस्मासुरक्षा चस्मा
3

Anneal

Heat each bar on fire bricks to a dull red with the torch and quench it in water.

यस चरणका सामग्री:

पानीपानी10 लिटर

चाहिने औजार:

प्रोपेन टर्चप्रोपेन टर्च
आगो सहने इँटाआगो सहने इँटा
आरनको सँड़सीआरनको सँड़सी
पानी दिने बाल्टिनपानी दिने बाल्टिन
4

Roll or hammer sheet and strip

Pass the flat bar through the rolling mill, closing it a little each pass, or hammer it on the anvil. Anneal whenever it stiffens. Cut strip from the sheet with snips.

चाहिने औजार:

बेल्ने मिलबेल्ने मिल
निहुँनिहुँ
तेर्सो फन्को भएको हथौडातेर्सो फन्को भएको हथौडा
पाता काट्ने कैँचीपाता काट्ने कैँची
डिजिटल क्यालिपर ६ इन्चडिजिटल क्यालिपर ६ इन्च
5

Draw rod

Hammer the square bar round, taper the end, and draw it through the drawplate with draw tongs and wax, annealing every few holes.

चाहिने औजार:

निहुँनिहुँ
गोलो टुप्पो भएको हथौडागोलो टुप्पो भएको हथौडा
फलामको तार तान्ने पाताफलामको तार तान्ने पाता
तान्ने सँड्सीतान्ने सँड्सी
बेन्चको भाइसबेन्चको भाइस
6

Clean

Soak in vinegar with salt to lift the oxide, scrub with the wire brush, rinse and dry.

यस चरणका सामग्री:

सिर्कासिर्का0.5 लिटर
नुननुन10 ग्राम

चाहिने औजार:

कचौराकचौरा
तार ब्रसको सेटतार ब्रसको सेट
7

Troubleshooting

Brass working troubleshooting.

Flow

Loading...

सामग्री

5
  • प्लेसहोल्डर
  • 5 केजी
    प्लेसहोल्डर
  • 10 लिटर
    प्लेसहोल्डर
  • 0.5 लिटर
    प्लेसहोल्डर
  • 10 ग्राम
    प्लेसहोल्डर

आवश्यक उपकरणहरू

22

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...