कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

सिर्जनाकर्ता

Penny

14. अक्टोबर 2026DK
२५
०
०
०
०

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
मध्यम
Two to three days

निर्देशनहरू

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

यस चरणका सामग्री:

चेप्टो टुल स्टिलको डन्डीचेप्टो टुल स्टिलको डन्डी1 टुक्रा

चाहिने औजार:

धातुको रेतीधातुको रेती
हाते ड्रिलहाते ड्रिल
डिजिटल क्यालिपर ६ इन्चडिजिटल क्यालिपर ६ इन्च
आरनको भट्टीआरनको भट्टी
पानी दिने बाल्टिनपानी दिने बाल्टिन
सुरक्षा चस्मासुरक्षा चस्मा
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

यस चरणका सामग्री:

कडा काठको साँघुरो पट्टीकडा काठको साँघुरो पट्टी2 टुक्रा
नरम फलामको गोलो डण्डीनरम फलामको गोलो डण्डी0.3 m

चाहिने औजार:

धातुको रेतीधातुको रेती
आरनको भट्टीआरनको भट्टी
पानी दिने बाल्टिनपानी दिने बाल्टिन
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

यस चरणका सामग्री:

पित्तलको पातापित्तलको पाता1 टुक्रा
मैन लगाइएको लिनेनको धागोमैन लगाइएको लिनेनको धागो3 m

चाहिने औजार:

पाता काट्ने कैँचीपाता काट्ने कैँची
हाते ड्रिलहाते ड्रिल
धातुको रेतीधातुको रेती
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

चाहिने औजार:

धातुको रेतीधातुको रेती
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

यस चरणका सामग्री:

पित्तलको ढिक्कापित्तलको ढिक्का2 केजी
कोइलाकोइला1 as required
ढलाइको बालुवाढलाइको बालुवा5 केजी

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
आगो सहने माटोको मुसाआगो सहने माटोको मुसा
मुसाको चिम्टामुसाको चिम्टा
ढलाइको साँचो बाकस (माथिल्लो र तल्लो)ढलाइको साँचो बाकस (माथिल्लो र तल्लो)
वेल्डिङका पन्जावेल्डिङका पन्जा
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

यस चरणका सामग्री:

पानीपानी1 लिटर

चाहिने औजार:

अङ्कित सिलिन्डरअङ्कित सिलिन्डर
धातुको रेतीधातुको रेती
7

A binary set of weights

Jupyter नोटबुक लोड हुँदैछ…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

सामग्री

9

आवश्यक उपकरणहरू

12

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...