सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

सिर्जनाकर्ता

Forge

13. नोभेम्बर 2026NO
१०
०
०
०
०

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
मध्यम
About 5 hours

निर्देशनहरू

1

How many balls

Jupyter नोटबुक लोड हुँदैछ…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

यस चरणका सामग्री:

इस्पात पाइप (बाक्लो भित्ता, चुर्केदार छेउ)इस्पात पाइप (बाक्लो भित्ता, चुर्केदार छेउ)1 टुक्रा

चाहिने औजार:

धातुको खरादधातुको खराद
तीन पन्जा भएको खराद चकतीन पन्जा भएको खराद चक
खरादको काट्ने औजारखरादको काट्ने औजार
डिजिटल क्यालिपर ६ इन्चडिजिटल क्यालिपर ६ इन्च
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

यस चरणका सामग्री:

पित्तलको गोलो डण्डीपित्तलको गोलो डण्डी1 टुक्रा

चाहिने औजार:

धातुको खरादधातुको खराद
तीन पन्जा भएको खराद चकतीन पन्जा भएको खराद चक
खरादको काट्ने औजारखरादको काट्ने औजार
सेन्टर ड्रिल सेटसेन्टर ड्रिल सेट
ड्रिल टुप्पाको सेटड्रिल टुप्पाको सेट
डिजिटल क्यालिपर ६ इन्चडिजिटल क्यालिपर ६ इन्च
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

चाहिने औजार:

खम्बा भएको ड्रिलखम्बा भएको ड्रिल
ड्रिल टुप्पाको सेटड्रिल टुप्पाको सेट
चुरो काट्ने सेटचुरो काट्ने सेट
बेन्चको भाइसबेन्चको भाइस
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

यस चरणका सामग्री:

तामाको नलीतामाको नली1 टुक्रा
टिन-सिसाको टाँकाटिन-सिसाको टाँका1 टुक्रा
फ्लक्सफ्लक्स1 टुक्रा

चाहिने औजार:

फलाम काट्ने आराफलाम काट्ने आरा
ड्रिल टुप्पाको सेटड्रिल टुप्पाको सेट
खम्बा भएको ड्रिलखम्बा भएको ड्रिल
बिजुली सोल्डरिङ आइरनबिजुली सोल्डरिङ आइरन
बेन्चको भाइसबेन्चको भाइस
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

यस चरणका सामग्री:

फलामका बल बियरिङफलामका बल बियरिङ1 टुक्रा
मेसिन स्क्रुमेसिन स्क्रु1 टुक्रा

चाहिने औजार:

मिलाउन मिल्ने पानामिलाउन मिल्ने पाना
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

यस चरणका सामग्री:

कडा काठको ढिक्काकडा काठको ढिक्का1 टुक्रा
कडा काठका किलाकडा काठका किला1 टुक्रा
काठको गोन्दकाठको गोन्द1 टुक्रा
होज कपलिङहोज कपलिङ1 टुक्रा

चाहिने औजार:

हाते आराहाते आरा
खम्बा भएको ड्रिलखम्बा भएको ड्रिल
ड्रिल टुप्पाको सेटड्रिल टुप्पाको सेट
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

सामग्री

11

आवश्यक उपकरणहरू

13

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...