सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)
Forge

सिर्जनाकर्ता

Forge

14. नोभेम्बर 2026NO
११
०
०
०
०

Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)

Robert Gibson Griswold's first tool-making lesson in Amateur Work (Boston, 1904): four centre punches from heavy to fine and nine pin, drift, offset and riveting punches, forged from carbon tool steel, finished with file and emery, then the point alone dipped in brine and the temper let run down from the hot stock to straw yellow.
मध्यम
A day for the set

निर्देशनहरू

1

His sizes

Jupyter नोटबुक लोड हुँदैछ…
2

Read Griswold

"The more work put into the steel at the working point the better will be its grade."
3

Forge the blanks

Forge carbon tool steel at no more than a bright red into the shapes of his fig. 2: a 3/8 in. chamfered head, a 2 1/2 in. body and a 1 1/2 in. taper. Heavy centre punch at least 5/8 in. across with a conical point about 3/8 in. at the base; lighter centre punches 3/8 and 1/4 in.; pin punches 1/2, 3/8 (square end), 5/16 and 1/4 in., plus parallel-ended, offset and round-ended ones.

यस चरणका सामग्री:

औजार इस्पातको डन्डीऔजार इस्पातको डन्डी1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
आरनको सँड़सीआरनको सँड़सी
4

Finish before hardening

Do all work except grinding the point now: file each punch to shape and finish it with emery cloth. Keep the striking head slightly rounded so it does not broom.

यस चरणका सामग्री:

कोरन्डम कपडाकोरन्डम कपडा1 टुक्रा

चाहिने औजार:

रेती (हातको रेती)रेती (हातको रेती)
5

Harden the point

Heat the point to a dull red and plunge only the point, about 1/2 in. (13 mm), into a brine bath.

यस चरणका सामग्री:

पूर्ण संतृप्त नुनको घोलपूर्ण संतृप्त नुनको घोल1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
आरनको सँड़सीआरनको सँड़सी
बाल्टिनबाल्टिन
6

Run the temper

When the point is black, rub a bright spot with emery cloth on a flat stick and watch the heat from the stock colour it. At straw yellow (460 F) plunge the whole punch in water and keep it moving. If the stock has too little heat, lay it over the furnace to draw the colour.

यस चरणका सामग्री:

पानीपानी1 टुक्रा
कोरन्डम कपडाकोरन्डम कपडा1 टुक्रा

चाहिने औजार:

बाल्टिनबाल्टिन
आरनको भट्टीआरनको भट्टी
7

Grind the points

Grind the points to shape after hardening without letting the edge turn blue; if it blues, grind back to hard metal.

चाहिने औजार:

टेबुलको घोट्ने मेसिनटेबुलको घोट्ने मेसिन
8

Troubleshooting

Punch troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" I, **Amateur Work** (Boston), vol. III (1903-04), pp. 273-275 and fig. 2 (checked on the archive.org scan amateurwork03bostrich). Metric figures and tools are ours.

सामग्री

4

आवश्यक उपकरणहरू

7

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...