सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने

Leader Harness Long Crupper: Folded Dock, Lay, Hip Straps, Carrier Straps and Tugs (Hasluck, Harness Making, 1904)
The leader horse's long crupper (F in Fig. 102) runs from the collar straps along the back to the tail, and carries the hip straps (H) that hold up the chain traces and the carrier straps (L) for the stretcher. This is the long crupper from Paul N. Hasluck's Harness Making (1904), with its folded dock, lay, 3 in dee, hip-strap tugs (K) and stretcher strap (M). Every size is his.
उन्नत
About 1-2 days
निर्देशनहरू
1
1
His sizes in centimetres
His sizes in centimetres
Jupyter नोटबुक लोड हुँदैछ…
2
2
Read Harness Making, ch. VIII
Read Harness Making, ch. VIII
"Cut the crupper from good leather 3 ft. 8 in. long and 5 in. wide, and make a split 9 in. long at the light end and another, 7 in. long, at the tail end."
3
3
Cut the body
Cut the body
Cut the crupper 3 ft 8 in by 5 in. Slit the light end 9 in and the tail end 7 in, leaving the points of the slits the full width in front and only cutting a little out of the corners. Narrow the tail-end points gradually to about 1-1/8 in and cut a little from the sides of each slit. Cut a lining for a foot or so of the tail end.
यस चरणका सामग्री:
हार्नेसको छाला1 टुक्राचाहिने औजार:
छाला काट्ने छुरी
नाप्ने फित्ता4
4
Fold the dock
Fold the dock
Cut soft leather 16 in by 3-1/2 in for the dock and shave the ends thin. Damp it well and turn both edges down so they overlap deeply along the centre. Bring both ends together, sides meeting flat but not flat sides together; holding the piece flat in the centre, turn the lower edge inwards and upwards, keeping the points together with the other hand. Nail each point to a board and keep it in shape until dry, when the dock will be firm.
यस चरणका सामग्री:
बेसिल छाला (भेडाको छाला)1 टुक्रा
काँटी1 टुक्राचाहिने औजार:
छाला काट्ने छुरी
स्पन्ज
घन
सल्लाको फल्याक5
5
Finish the body and put in the dock
Finish the body and put in the dock
Edge, crease and black the body, making two rows all round; rub the edges well and hot-crease the lines. At the tail end prick the second line as far as the double runs. When the dock is dry, put it between the lining and body at each end of the slit, tack it down round the lining and stitch. A few egg-shaped stitches inside the outer stitches, through the body and dock points, keep the dock in place. Trim the edges and black, rub and tallow them, and the inside edges of the slits too.
यस चरणका सामग्री:
छालाको रङ1 टुक्रा
बोसो1 टुक्रा
लास्टिङ किला1 टुक्रा
छालाको धागो1 टुक्रा
मौरीको मैन1 टुक्राचाहिने औजार:
किनारा च्याम्फर गर्ने औजार
खोप पार्ने औजार
प्रोपेन टर्च
छालाको किनारा घोट्ने औजार
छालाको सिलाई छिनो
घन
आर (छेड्ने सियो)
दुई काठी सिलाउने सियो
छाला सिलाइ च्याप्ने काठ6
6
Fit the front buckles
Fit the front buckles
Cut two chapes to hold the buckles in front that fasten the crupper to the collar straps; bend them down about 4 in, shave one end and point the other, and cut a hole for the buckle. Tack two loops about 1-1/2 in wide in place, keeping the outside of each buckle exactly level with the end of its slit and the chapes right in the centre. Stitch them down, put a cross stitch on each side of the buckle, and shape and crease the loops.
यस चरणका सामग्री:
हार्नेसको छाला1 टुक्रा
जिब्रो भएको फलामे बकल2 टुक्रा
छालाको धागो1 टुक्रा
मौरीको मैन1 टुक्राचाहिने औजार:
छाला काट्ने छुरी
लुप स्टिक
खोप पार्ने औजार
प्रोपेन टर्च
आर (छेड्ने सियो)
दुई काठी सिलाउने सियो
छाला सिलाइ च्याप्ने काठ7
7
Make the lay, hip straps and carrier straps
Make the lay, hip straps and carrier straps
Cut the lay 1 ft 3 in by 3 in, turn it down for about 1 ft at the good end, shave the end of the short turn thin and round the other end; edge, crease and black it. Cut two hip straps 2 ft by 1-1/2 in, turn them down 3 in at the heavy end, shave the turn-down, point the buckle end, and crease and black them. Attach them to a 3 in japanned or tinned dee, one on each side, with four rows of stitching in the double of each; rub and finish the edge. Make two carrier straps the same way, each 2 ft 10 in by 1-1/4 in, and stitch them in the middle round part of the dee between the hip straps.
यस चरणका सामग्री:
हार्नेसको छाला1 टुक्रा
साजको D-औंठी1 टुक्रा
छालाको रङ1 टुक्रा
छालाको धागो1 टुक्रा
मौरीको मैन1 टुक्राचाहिने औजार:
छाला काट्ने छुरी
किनारा च्याम्फर गर्ने औजार
खोप पार्ने औजार
प्रोपेन टर्च
छालाको किनारा घोट्ने औजार
आर (छेड्ने सियो)
दुई काठी सिलाउने सियो
छाला सिलाइ च्याप्ने काठ
नाप्ने फित्ता8
8
Stitch the dee and lay to the body
Stitch the dee and lay to the body
Put the straight part of the dee in the bend of the lay and place it on the centre of the crupper body, the same distance from each side, with the extreme point of the dee within 8 in of the points of the tail slits. Tack down and stitch two rows 1/4 in apart all round, eight per inch, with three-cord thread; then stitch the lay coarse, or spot it across just to the dee. Some makers put a pad under the crupper, as on the cart-saddle crupper, from the end of the tail slit to 1 in beyond the point of the lay.
यस चरणका सामग्री:
लास्टिङ किला1 टुक्रा
छालाको धागो1 टुक्रा
मौरीको मैन1 टुक्राचाहिने औजार:
घन
छालाको सिलाई छिनो
आर (छेड्ने सियो)
दुई काठी सिलाउने सियो
छाला सिलाइ च्याप्ने काठ9
9
Make the hip-strap tugs and stretcher strap
Make the hip-strap tugs and stretcher strap
With a pair of 1-1/2 in hip-strap chains, cut the tugs 10 in by 1-1/2 in; bend them so the points meet in the centre, cut a hole for the buckle in one end, stitch the points together and put in two narrow loops (one hides the joint) or one broad loop. Stitch a safe underneath. For the stretcher carrier tug, cut a strap 1-1/4 in by 1 ft 2 in, bend a chape in it and cut a hole for the buckle; stitch the buckle on with a loop, and make a running loop and a hole 1 in from the point of the strap.
यस चरणका सामग्री:
फलामको सिक्री2 टुक्रा
हार्नेसको छाला1 टुक्रा
जिब्रो भएको फलामे बकल3 टुक्रा
छालाको धागो1 टुक्रा
मौरीको मैन1 टुक्राचाहिने औजार:
छाला काट्ने छुरी
लुप स्टिक
छालामा प्वाल पार्ने पन्च
आर (छेड्ने सियो)
दुई काठी सिलाउने सियो
छाला सिलाइ च्याप्ने काठ10
10
Put the gear together
Put the gear together
Fix a loop on each end of the stretcher and nail its ends, leaving room for the strap to pass. Put the runner loop on the strap, run the strap down through the stretcher loop and back through the runner to the buckle; secure the carrier straps to the same buckle, their points down in the loop, and keep the runner down by the stretcher. Buckle the hip straps into the tug buckles, hook the chain traces on, and buckle the collar straps into the front buckles. The dock under the tail is optional: the hip straps fastened in the dee keep the crupper in place.
यस चरणका सामग्री:
हार्नेसको छाला1 टुक्रा
काँटी1 टुक्राचाहिने औजार:
घन
छाला काट्ने छुरी11
11
Troubleshooting
Troubleshooting
Long crupper troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
From **Harness Making**, edited by Paul N. Hasluck, Cassell, 1904 (Project Gutenberg 70169), chapter VIII, "Fore Gear or Leader Harness", pp. 101-104, Figs. 102-104; every fraction was checked on the archive.org scan (harnessmaking00hasl). The stretcher (the bar that keeps the traces apart) is not made here. Basil for the "soft leather" dock, the buckle count in the list, the tools and metric figures are ours.
सामग्री
11- 5 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 2 टुक्राप्लेसहोल्डर
- 2 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 5 टुक्राप्लेसहोल्डर
- 5 टुक्राप्लेसहोल्डर
- 3 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 2 टुक्राप्लेसहोल्डर
आवश्यक उपकरणहरू
15- प्लेसहोल्डर
- 1 vendor sell this, none ship to you yetप्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
यो खाकाले बनाउँछ
सम्बन्धित ब्लुप्रिन्ट
यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त
CC0 सार्वजनिक डोमेन
यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।
ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।


