सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

सिर्जनाकर्ता

Forge

14. नोभेम्बर 2026NO
८
०
०
०
०

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
शुरुआती
Two hours

निर्देशनहरू

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

यस चरणका सामग्री:

औजार इस्पातको चेप्टो पाटोऔजार इस्पातको चेप्टो पाटो1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
आरनको सँड़सीआरनको सँड़सी
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

यस चरणका सामग्री:

चुन (क्याल्सियम हाइड्रोक्साइड)चुन (क्याल्सियम हाइड्रोक्साइड)1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
आरनको सँड़सीआरनको सँड़सी
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

चाहिने औजार:

खम्बा भएको ड्रिलखम्बा भएको ड्रिल
बेन्चको भाइसबेन्चको भाइस
रेती (हातको रेती)रेती (हातको रेती)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

यस चरणका सामग्री:

कडा काठको फल्याककडा काठको फल्याक1 टुक्रा

चाहिने औजार:

हाते आराहाते आरा
बेन्चको भाइसबेन्चको भाइस
रेती (हातको रेती)रेती (हातको रेती)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
पानी दिने बाल्टिनपानी दिने बाल्टिन
धार लगाउने ढुङ्गाधार लगाउने ढुङ्गा
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

सामग्री

3

आवश्यक उपकरणहरू

10

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...