SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall
Millie

Nilikha ni

Millie

7. Oktubre 2026NL
39
0
0
0
0

Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall

A. C. Stiles of South Bloomfield, Ohio, received US 3,764, dated 27 September 1844, for a rocking churn: an oblong box on rockers, split by a partition with holes, with a dasher on each side worked by arms on shafts across the ends, and one upright lever that rocks the box and works the dashers together. This rung prints the partition, dashers and arms, builds the box and makes butter.
Abantado
About 6 hours, plus printing

Mga Tagubilin

1

One lever, three motions

Naglo-load ng Jupyter notebook…
2

Two dashers from one lever, before it

Mitchell worked two dashers from one lever; Stiles adds rockers and a perforated partition between them.
3

Read US 3,764

"The machine is operated by moving the upright lever l, to and fro, which rocks the box, while at the same time it works the dashers up and down, thus throwing the cream through the partition d, till the butter is made."
4

Print the parts

Print the partition (/uploads/blueprints/rocking-twin-dasher-lever-churn-partition.stl), two dashers (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher.stl), two dasher arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher-arm.stl) and two lower arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-lower-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Mga materyales para sa hakbang na ito:

PETG filamentPETG filament1 piraso

Mga kailangang kasangkapan:

Limbagang 3D na FDMLimbagang 3D na FDM
5

Box on rockers

Build a pine box about 260 × 120 × 150 mm with a close-fitting lid, sealed inside. Glue the partition across its middle and screw two curved pine rockers lengthwise underneath. Drill the lid for the two dasher handles.

Mga materyales para sa hakbang na ito:

Tablang pinoTablang pino1 piraso
Pandikit sa KahoyPandikit sa Kahoy1 piraso
Silicone SealantSilicone Sealant1 piraso
Turnilyong pangkahoy #8 x 1"Turnilyong pangkahoy #8 x 1"1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
Lagaring PangkurbaLagaring Pangkurba
Walang-Kableng BarenaWalang-Kableng Barena
Hanay ng Talim ng BarenaHanay ng Talim ng Barena
Mga clampMga clamp
6

Shafts, arms and lever

Set a 10 mm square shaft across each end on two studs, 60 mm above the lid. Fit a dasher arm on each, pointing inward and pinned to its dasher's handle, and a lower arm on each outside the box. Join the lower arms with a pine bar, and pivot an upright pine lever on a block near the box's foot, pinned to the bar's middle.

Mga materyales para sa hakbang na ito:

Mga tarugong matigas na kahoyMga tarugong matigas na kahoy1 piraso
Tablang pinoTablang pino1 piraso
Bilog na Bara ng Malambot na AseroBilog na Bara ng Malambot na Asero1 piraso
Mga turnilyo ng makinaMga turnilyo ng makina1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
Walang-Kableng BarenaWalang-Kableng Barena
Hanay ng Talim ng BarenaHanay ng Talim ng Barena
Set ng mga distornilyadorSet ng mga distornilyador
7

The patent drawing

US 3,764 drawing sheet, public domain (expired patent).
Hakbang 7 - Image 1
8

Rock and churn

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Work the lever to and fro: the box rocks and the dashers rise and fall in turn. Keep fingers clear of the arms and the rockers. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.

Mga materyales para sa hakbang na ito:

Makapal na kremaMakapal na krema1500 ml
Magaspang na Asin sa DagatMagaspang na Asin sa Dagat1 piraso
TubigTubig1 piraso

Mga kailangang kasangkapan:

Termometro na naiiwang nakatusokTermometro na naiiwang nakatusok
Panukat ng OrasPanukat ng Oras
Digital na Timbangang PangkusinaDigital na Timbangang Pangkusina
Malaking mangkok na panghalo na asero na hindi kinakalawangMalaking mangkok na panghalo na asero na hindi kinakalawang
9

Troubleshooting

Rocking twin-dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**A. C. Stiles** of South Bloomfield, Pickaway County, Ohio, US 3,764, 27 September 1844. He claimed the combination of the rockers and dashers in the double-chambered churn. His drawing gives no sizes; ours are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.

Mga Materyales

11

Mga Kinakailangang Kasangkapan

11

Ang blueprint na ito ay gumagawa ng

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...