Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)
Woody

Autor

Woody

13. listopad 2026NO
4
0
0
0
0

Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)

Harry Hardy's monorail sled from The Boy Mechanic, Book 2 (1915): two plank runners one behind the other under a 6 ft board, shod with square-edged strap iron that grips like a skate. The rider lies full length and steers the front runner with a bar, balancing like a cyclist.
Średniozaawansowany
About 1 day

Instrukcje

1

His sketch in centimetres

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 2

"Round iron or half-round iron should not be used, as these are liable to skid. The square, sharp edges of the strap iron prevent this and grip the surface just as a skate."
3

Cut and shoe the runners

Cut the two runners from 1 in plank to the size and shape of his sketch: the front runner 2 ft long, the rear one 2-1/2 ft long and about 1 ft high (the sketch prints the rear length with an inch mark; it is drawn as 2-1/2 ft). Shoe them with strap iron 1 in wide and 1/4 in thick, keeping the edges square and sharp.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Piłka włosowaPiłka włosowa
Piła do metaluPiła do metalu
Imadło warsztatoweImadło warsztatowe
Wiertarka ręcznaWiertarka ręczna
OłówekOłówek
Miara zwijanaMiara zwijana
4

Fit the rear runner

Nail or bolt blocks on either side of the upper edge of the rear runner and screw the top board (6 ft long, 1 in thick) to them. Brace the runner with strap iron, as in the sketch.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Śruba zamkowaŚruba zamkowa1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Piła do metaluPiła do metalu
Wiertarka ręcznaWiertarka ręczna
MłotekMłotek
5

Fit the front runner and steering

Fit the front runner the same way, but with only one pair of blocks at the centre and a thin piece of wood on their tops as the fifth wheel. Bore the hole for the steering post 6 in from the front end of the top, a little larger than the post. Round the post where it passes through the hole and leave its upper end square, to take the steering bar tightly.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Świder korbowy z wiertłemŚwider korbowy z wiertłem
DłutaDłuta
Strug ręcznyStrug ręczny
6

Troubleshooting

Monorail sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Monorail Sled" by Harry Hardy, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 50). The rear runner length is printed 2-1/2 with an inch mark but drawn longer than the 2 ft front runner, so it is read here as 2-1/2 ft. He gives no sizes for the blocks, braces or steering bar. The tools and metric figures are ours.

Materiały

5

Wymagane narzędzia

11

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...