Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Ice-Chamber Air Churn: The Hollow Dasher Pumps the Same Air Round Through Ice and Cream
Buttercup

Autor

Buttercup

9. listopad 2026IE
7
0
0
0
0

Ice-Chamber Air Churn: The Hollow Dasher Pumps the Same Air Round Through Ice and Cream

James H. Bump of Morris, New York, received US 21,871, dated 26 October 1858, for a churn with an ice chamber on its lid. A hollow dasher with a valve draws air from the ice chamber on every up stroke and forces it into the cream on every down stroke; the air pushed up out of the case returns through a tube into the ice chamber, so the same air goes round, cooled each time. This rung builds it in a 20-litre bucket with printed parts and a lever.
Średniozaawansowany
About 5 hours, plus printing

Instrukcje

1

Air, depth and lever

Wczytywanie notatnika Jupyter…
2

Air through a hollow dasher, before it

Marcell blew room air down a hollow dasher shaft. Bump draws it from an ice chamber and sends it round again.
3

Read US 21,871

"At every upward movement of the staff F, the air from the chamber C, rushes down within the staff F, into the chamber d ... and as the dasher descends the valve e, closes and the air within will be forced into the cream j, and at the same time the air in the case above the cream will be compressed by the rising of the cream j ... and said air will pass up the space f, into the chamber C".
4

Print the tube E

Tube E, 40 mm across and 155 mm long, with its flange under lid B. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
5

Print the clamp ring

The ring that clamps tube E's flange, lid B and the chamber floor together. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
6

Print the box a

Upper box a, 110 mm tall, with the staff's top guide. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
7

Print the box a'

Lower box a', with the four notches that do the work of Bump's grooves. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
8

Print the dasher G

The bell dasher, 160 mm across, with chamber d open below. It needs a 160 mm bed; print it top down. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
9

Print the flap e

The valve flap with its two hinge knuckles. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
10

Print the staff head

The block that closes the staff's top and takes pin h. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Plik projektowySTLCC0 - Free
11

Lid, tube and ice chamber

Use a food-grade 20-litre bucket and its lid (lid B), and a round food container 200 mm across and 130 mm deep as chamber C, its own lid as lid D. Cut a 40 mm hole in the middle of lid B and of the container's floor. Push tube E up from under lid B, set the container on the lid and the clamp ring over the tube, and fix them with four M4 screws and lock nuts. Cut a 30 mm hole in the middle of lid D.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka
Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Pojemnik do przechowywania klasy spożywczejPojemnik do przechowywania klasy spożywczej1 sztuka
Śruby maszynoweŚruby maszynowe4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Zestaw otwornicZestaw otwornic
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
Klucz nastawnyKlucz nastawny
12

Boxes and hollow staff

Bolt box a on top of lid D and box a' under it through their flanges, three M4 screws, the notches of a' against the lid. Cut the stainless tube (16 mm, 1 mm wall) to 549 mm. Drill two 5 mm holes c straight through it, crossed, 389 mm from its foot, and a 4.4 mm hole across it 6 mm and 534 mm from its foot for the cross screws.

Materiały do tego kroku:

Śruby maszynoweŚruby maszynowe3 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową3 sztuk
Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Obcinak do rurObcinak do rur
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Zestaw wkrętakówZestaw wkrętaków
13

Dasher and valve

Hang the flap e on the lug in the dasher's chamber with an M3 screw and lock nut so it covers the air hole from below and swings down freely. Push the staff's foot 12 mm into the dasher's top and fix it with an M4 screw across.

Materiały do tego kroku:

Śruby maszynoweŚruby maszynowe2 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową2 sztuk

Potrzebne narzędzia:

Zestaw wkrętakówZestaw wkrętaków
Klucz nastawnyKlucz nastawny
14

Upright and lever

Cut a hardwood foot 90 x 34 x 30 mm and bolt it to lid B 120 mm from the middle, with two M6 bolts through a hardwood backing strip under the lid. Screw a hardwood upright 30 x 45 mm, 337 mm tall, on it. Cut two lever strips 30 x 12 mm, 480 mm long; drill each 20 mm from one end for pin g and cut a 6.5 mm slot from 110 to 135 mm past it for pin h. Lower the staff through tube E and the boxes, push on the staff head with an M4 screw across, and bolt the strips either side of the upright (pin g) and of the head (pin h) with M6 bolts, washers and lock nuts.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych4 sztuk
Podkładka płaskaPodkładka płaska8 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową5 sztuk
Wkręt do drewna #8 x 1"Wkręt do drewna #8 x 1"4 sztuk
Śruby maszynoweŚruby maszynowe1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Papier ściernyPapier ścierny
Klucz nastawnyKlucz nastawny
Miara zwijanaMiara zwijana
15

The build in 3D

FreeCAD model of this build at mid stroke, the near quarter of the bucket, chamber and boxes cut away: lid B with tube E, chamber C and lid D, boxes a and a', the hollow staff with its holes c, the bell dasher with flap e, the upright and the forked lever.
Plik projektowyBLENDCC0 - Free
16

Churn

Pour 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer. Fit lid B with the dasher in place, fill chamber C with crushed ice round tube E and close lid D. Work the lever up and down steadily, the full 100 mm stroke, and time it. When the butter comes, lift the lid out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Lód rozdrobnionyLód rozdrobniony2 kg
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
17

Troubleshooting

Ice-chamber churn troubleshooting.

Flow

Loading...
18

History and honest limits

**James H. Bump** of Morris, Otsego County, New York, US 21,871, 26 October 1858, "Churn". He held that the cream, "by the absorption of oxygen is fully acetified" and kept cool by the iced air, gives butter "of a superior quality". He disclaimed a hollow dasher rod for air and forcing air into cream as done before, and claimed only the chamber C through which the air is made to circulate. He gave no sizes and named only "metal boxes": every size, material and the 8 litres at 15 °C are ours. Our notches in box a' stand in for his grooves cut in lid D.

Materiały

14

Wymagane narzędzia

15

Pliki projektowe

8

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...