Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Rocking Bucket-Dasher Churn: A Crank and Rod Rock a Dasher of Bucketed Arms, a Fixed Bucket Breaks the Current
Gillett Bunting of Liberty, Indiana, received US 26,226, dated 22 November 1859, for a churn-dasher. A dasher of crossed arms with buckets on their ends rocks on a level shaft whose bearings slide up or down to suit the amount of cream. A crank above, turned through a pair of cog wheels with a balance wheel, rocks it by a long rod, throwing the cream into opposing currents, and a fixed bucket on the bottom breaks the current along the floor.
The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing
Instrukcje
1
1
How far the dasher rocks
How far the dasher rocks
Wczytywanie notatnika Jupyter…
2
2
Agitators swung on pivots, two weeks before
Agitators swung on pivots, two weeks before
Cooper swings his agitators from a dash rod worked by hand. Bunting rocks a whole dasher from a crank.
3
3
Read US 26,226
Read US 26,226
"the rapid oscillating motion thus imparted to the dasher, through the medium of buckets (e' g', K) forces the cream into violent opposing currents, at the same time, the concussive action of the buckets (e', g') and arms (e, g) and bar (E) upon the cream is fully developed, thereby producing, a rapid and violent agitation of the cream"
4
4
Print the driving wheel G
Print the driving wheel G
Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the wheel h
Print the wheel h
Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 12.6 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Shell A, bed A', guides L and bucket K
Shell A, bed A', guides L and bucket K
Use a wooden tub 360 mm across inside at the floor, 320 mm at the top and 420 mm deep. Stand it on a bed board 520 x 560 mm between two guide strips. Glue and screw a hardwood block K, 60 x 300 x 60 mm, across the middle of the floor, with a 24 x 24 mm socket 50 mm deep near each end for the slides. Fill the tub with water overnight so it swells tight, then empty it.
Materiały do tego kroku:
Drewniana balia1 sztuka
Deska z drewna liściastego2 sztuk
Klej do drewna1 sztuka
Wkręty do drewna12 sztukPotrzebne narzędzia:
Pilarka stołowa
Piła ręczna
Dłuto do gniazd
Pobijak drewniany
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Ścisk stolarski listwowy
Miara zwijana
Woda7
7
Slides f and the dasher
Slides f and the dasher
Cut two slides 20 x 24 mm, 255 mm long, bore each 21 mm 225 mm from its foot for the shaft's journal, and a row of 6 mm holes near the foot for a set screw through the block K. Make the shaft F a 20 mm hardwood dowel 280 mm long. Mortise through it two arms e 20 x 30 mm, 210 mm long, 150 mm apart, two arms g 20 x 30 mm, 260 mm long, at right angles to them, 80 mm apart, and the bar E 20 x 30 mm, 235 mm long, between the arms e, its long end reaching 100 mm past the shaft and bored 12.6 mm. Screw three U-channel buckets 170 x 40 x 20 mm of hardwood across the ends: one on the arms e and E's short end, one on each end of the arms g. Stand the slides in K with the shaft's ends in them, 240 mm up.
Materiały do tego kroku:
Deska z drewna liściastego2 sztuk
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztuka
Wkręty do drewna24 sztuk
Zestaw śrub sześciokątnych2 sztukPotrzebne narzędzia:
Pilarka stołowa
Frezarka górnowrzecionowa
Dłuto do gniazd
Pobijak drewniany
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Papier ścierny
Miara zwijana8
8
Frame B, crank shaft C, wheels and rod D
Frame B, crank shaft C, wheels and rod D
Bolt two posts of 40 x 30 mm hardwood to the bed beside the tub, 400 mm apart, 850 mm tall, and bore them 12.6 mm 690 mm above the tub's floor. Bend a 12 mm stainless shaft C into a crank of 50 mm throw in its middle, heating the bends red with the torch, and run it through the posts over the bar E's end. Pin the wheel h on one end and a hardwood balance wheel k, 260 mm across and 30 mm thick, on the other. Fix a 20 mm stud above h for the wheel G, meshing, with a crank handle H. Join the crank to E's end with a hardwood rod D, 450 mm between its pins.
Materiały do tego kroku:
Drewno iglaste 70x70 mm1 sztuka
Deska z drewna liściastego2 sztuk
Pręt ze stali nierdzewnej2 sztuk
Shaft Collar2 sztuk
Zawleczka4 sztuk
Podkładka płaska6 sztuk
Zestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonową4 sztuk
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Palnik propanowy
Imadło warsztatowe
Młotek
Rękawice żaroodporne
Wyrzynarka
Kompas
Piła do metalu
Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Klucz nastawny9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the tub cut through the middle: the bed and guides, the fixed bucket K with the two slides, the dasher with its arms, bar E and three buckets, the rod D up to the cranked shaft C, the wheels G and h, the crank H and the balance wheel. The crank was turned through 24 positions.
10
10
Churn
Churn
Pour in heavy cream at about 15 °C, checked with the thermometer; for less cream, lower the slides in K so the dasher still works in it. Turn the crank H steadily, timing it. When the butter comes, lift the rod off the crank and the dasher out on its slides, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka15 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej11
11
Troubleshooting
Troubleshooting
Rocking dasher troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Gillett Bunting** of Liberty, Union County, Indiana, assignor to himself and W. M. Jarrell, US 26,226, 22 November 1859, "Churn-Dasher". He disclaimed hinged churn-dashers and oscillating movement as such, and claimed the vibrating movement of the dasher by the arms with the crank, driving wheel and connecting rod, with the current breaker K. The patent gives no sizes; every size here is ours. His frame B stands on the shell's top; ours is two posts on the bed beside it.
Materiały
16- 1 sztukaZastępnik
- 2 sztukZastępnik
- 2 sztukZastępnik
- 36 sztukZastępnik
- 1 sztukaZastępnik
- 6 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 2 sztukZastępnik
- 4 sztukZastępnik
- 6 sztukZastępnik
- Zastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
25- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
3Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Folding-Lever Dasher Churn: The Dash Rod Folds Two Levers and Swings the Agitators Side to Side
autor: Buttercup
Obróbka drewna
7
0
0
0
0
0

Segmental-Stave Churn: Thick Curved Staves Split the Cream's Current, a Long Blade Sweeps Beneath Them
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

