Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Segmental-Stave Churn: Thick Curved Staves Split the Cream's Current, a Long Blade Sweeps Beneath Them
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Segmental-Stave Churn: Thick Curved Staves Split the Cream's Current, a Long Blade Sweeps Beneath Them

Thomas A. Jebb of Buffalo, New York, received US 26,109, dated 15 November 1859, for a churn. Three of the tub's staves are made much thicker on one edge, curving inward, so the turning cream rides up their faces, rebounds and eddies in their lee. A dash of five wedge-shaped blades at right angles turns on an upright shaft; the lowest blade is long and sweeps under the staves' bevelled ends so nothing lodges on the bottom. The gearing sits on a hinged cross piece clear of the cream. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

Long blade under, short blades within

Wczytywanie notatnika Jupyter…
2

Breaking the turning cream on the tub's wall, two months before

Taylor fixed thin brakes and ledges to the wall. Jebb makes three staves themselves thick and curved, and runs a long blade under them.
3

Read US 26,109

"The dash blades are caused to revolve by turning the crank S, the bevel face (k-l) of the blade striking against the cream causing a portion of it to pass up the incline face (k-l) and fall down on the line (l-m) while a portion is thrown from B, to B, with a rebound, and a portion forms an “eddy” and backward current in the “lee” of the thick edge of, B."
4

Print the wheel Q

Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion P

Spur pinion, 12 teeth, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the bearing n

A cup 50 mm across and 15 mm tall with a 20 mm socket for the shaft's foot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Tub A and staves B

Use a wooden tub 270 mm across inside at the floor, 300 mm at the top and 380 mm deep. From hardwood cut three segments to lie against the wall over 60 degrees each, thin at one edge and rising on a quarter circle to 44 mm thick at the other, 330 mm tall. Bevel each one's foot upward towards the middle, from 50 mm up at the wall to 95 mm at its thick edge. Glue and screw them inside, a third of the way round from each other, all thick edges facing the same way round. Glue the bearing cup in the middle of the floor. Fill the tub with water overnight so it swells tight, then empty it.

Materiały do tego kroku:

Drewniana baliaDrewniana balia1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna18 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
WyrzynarkaWyrzynarka
Strug kabłąkowyStrug kabłąkowy
Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Miara zwijanaMiara zwijana
WodaWoda
8

Dash: shaft I and blades H, H2

Turn a hardwood shaft 30 mm across and 400 mm long, its foot turned to 19 mm for 11 mm, and fit a 12 mm stainless pin 52 mm long in its top for the pinion. Cut five blades 40 x 15 mm and shave each to a wedge, its two faces bevelled opposite ways. Make the lowest 256 mm long and the other four 164 mm. Mortise them through the shaft at positions 25, 100, 160, 220 and 280 mm above the tub's floor, each at right angles to the one below.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Dłuto do gniazdDłuto do gniazd
Pobijak drewnianyPobijak drewniany
Strug kabłąkowyStrug kabłąkowy
Piła do metaluPiła do metalu
Papier ściernyPapier ścierny
Miara zwijanaMiara zwijana
9

Cover, cross piece M and gearing

Cut a round cover in two halves to rest on the staves' tops, with a 32 mm hole for the shaft. Hinge a hardwood cross piece M, 60 x 20 mm, across the tub's top with a strap hinge on one side (g2), resting on a cleat on the other (g3), bored 14 mm for the shaft's pin. On it screw two chairs carrying a 12 mm stainless shaft R with the crown wheel and a crank S, and pin the pinion on the shaft's top so the two mesh. Lift M on its hinge to free the shaft.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Zawias pasowy żelaznyZawias pasowy żelazny1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
KompasKompas
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Zestaw wkrętakówZestaw wkrętaków
10

The build in 3D

FreeCAD model of this build, the tub and cover cut through the middle: the three curved staves with their bevelled feet, the dash with its long lower blade and four short ones, the bearing, and the cross piece with the crown wheel, pinion and crank. The dash was turned through 36 positions.
Plik projektowyBLENDCC0 - Free
11

Churn

Pour in heavy cream at about 15 °C, checked with the thermometer, from a few litres up to about 12, put the cover halves and the cross piece down, and turn the crank steadily, timing it. When the butter comes it rises to the top: lift M and the cover, take the butter out, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka12 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
12

Troubleshooting

Segmental-stave churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Thomas A. Jebb** of Buffalo, New York, US 26,109, 15 November 1859, "Churn". He claimed the short dash blades H and the long blade H2 arranged with the segmental stave B, the short blades turning within and the long one under its bevelled end, and the blades' arrangement with the staves. His thick staves are single solid staves of the tub "leaving no interstice in the stave for the milk to lodge in and get sour"; ours are segments fixed inside a bought tub. His bevel pinion and wheel are here a printed pinion and crown wheel. The patent gives no sizes; every size here is ours.

Materiały

11

Wymagane narzędzia

21

Pliki projektowe

4

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...