Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut
Buttercup

Autor

Buttercup

11. listopad 2026IE
8
0
0
0
0

Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut

S. N. Campbell of Elgin, Illinois, received US 25,804, dated 18 October 1859, for a churn. A lever pivoted on a post works a dasher that fits the box closely. Its hinged slats hang open as deflectors: drawn up, the dasher throws the cream down and to the sides; pushed down, it forces the cream up towards a cross piece in the middle. A button with two inclined surfaces on the rod's foot holds the slats open, or, turned half round, lets them shut on the down stroke, to suit the cream. The patent gives no sizes and does not say where the slats are hinged or how the button bears on them: those and every size here are ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

The button: holding the slats open, or letting them shut

Wczytywanie notatnika Jupyter…
2

An up-and-down dasher fitting a box closely, three weeks before

Austin's middle dasher is a plain plate. Campbell's has hinged slats that deflect the cream, held open or let shut by a button on the rod.
3

Read US 25,804

"This dasher is constructed with movable slats H, H, which, when open, rest upon stop pins a, and serve the office of deflectors, and as the dasher is drawn up the cream is thrown below the slats and to the sides of the churn and as the dasher is pressed down the cream will be forced up and toward the center of the churn, and against a cross piece J, secured to the center of the dasher."
4

Print the button K

A disc 72 mm across and 6 mm thick with two inclined surfaces 60 mm long, one each side, both rising 7.5 mm towards the same end. PETG, 0.2 mm layers, 100 % infill.
Plik projektowySTLCC0 - Free
5

Box A, stand B, post D, lid E and lever C

From 20 mm hardwood make a box 400 x 300 mm and 380 mm deep inside, on four legs 50 mm square and 300 mm long. Screw a post 50 x 40 mm, 860 mm long, up the middle of the back. Cut a lid with a 32 mm hole in its middle. Bolt a lever 30 x 30 mm, 640 mm long, to the post's top so it reaches over the lid's middle to the front. Fill the box with water overnight so it swells tight, then empty it.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Drewno iglaste 70x70 mmDrewno iglaste 70x70 mm1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna30 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych2 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową2 sztuk
Podkładka płaskaPodkładka płaska4 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Piła ręcznaPiła ręczna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
Kątownik stolarskiKątownik stolarski
Miara zwijanaMiara zwijana
WodaWoda
Klucz nastawnyKlucz nastawny
6

Dasher G and its slats

Make two end bars 296 x 40 x 20 mm and join them with the cross piece J, 396 x 40 x 30 mm, bored 31 mm in its middle. Cut two inner slats H 380 x 63 x 12 mm, each with a tab 20 x 9 mm on its inner edge 10 to 30 mm from the middle, and two outer slats H' 380 x 52 x 12 mm. Bore each along its length for a 6 mm stainless hinge pin, H 3 mm in from its inner edge and H' 4 mm in, and hang them between the end bars on pins 392 mm long, H 32 mm and H' 98 mm each side of the middle. Fix 6 mm stop pins, 20 mm long, into the end bars under the slats: 80 mm out and 27 mm below the hinges for H, 130 mm out and 21.5 mm below for H'. Glue posts 20 x 10 x 19 mm on the slats, 120 mm each side of the middle, 40 mm out from each hinge, and join each pair with a piece L 76 x 20 x 6 mm on pins.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Klej do drewnaKlej do drewna1 sztuka
ZawleczkaZawleczka12 sztuk
Podkładka płaskaPodkładka płaska12 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Papier ściernyPapier ścierny
Miara zwijanaMiara zwijana
Ścisk stolarski listwowyŚcisk stolarski listwowy
7

Rod F and button K

Turn a hardwood rod F 30 mm across and 440 mm long, with a cross handle at its top to turn it. Pass it down through J and glue the button on its foot, below J, so that in one position its inclined surfaces lie under the slats' tabs and hold the slats open on their pins. Join its top to the lever with a pin in a slot. Set the dasher in the box and the lid on.

Materiały do tego kroku:

Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
ZawleczkaZawleczka2 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
8

The build in 3D

FreeCAD model of this build, one side and one end left off: the box on its stand, the post and lever, the rod, and the dasher with the cross piece J, the hinged slats H and H' on their stop pins, the pieces L and the button K under the tabs. Checked at three heights, with the slats held open and with them shut.
Plik projektowyBLENDCC0 - Free
9

Churn

Pour about 20 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Work the lever up and down, timing it. For thin cream keep the button holding the slats open; if the cream thickens, turn the rod half round so the slats shut on each down stroke. When the butter comes, lift the dasher out, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka20 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
10

Troubleshooting

Hinged-slat dasher troubleshooting.

Flow

Loading...
11

History and honest limits

**S. N. Campbell** of Elgin, Kane County, Illinois, US 25,804, 18 October 1859, "Churn". He claimed "the arrangement and combination of the button K, dasher rod F, movable slats H, H', pieces L, and bar J". The patent gives no sizes and does not say where the slats are hinged, how the button's surfaces bear on them, or how the pieces L join H' to H: the hinge lines, the tabs, the button's surfaces, the links and every size here are our reading.

Materiały

14

Wymagane narzędzia

18

Pliki projektowe

2
  • campbell-button-set-hinged-slat-dasher-churn-button-k.stlSTLCC0
  • campbell-button-set-hinged-slat-dasher-churn.blendBLENDCC0

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...