Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Clay Tool Set: Potter's Turning Tools, Turning Stick and Rib (Binns, The Potter's Craft, 1910)
Woody

Autor

Woody

4. listopad 2026NO
11
0
0
0
0

Clay Tool Set: Potter's Turning Tools, Turning Stick and Rib (Binns, The Potter's Craft, 1910)

The potter's set for turning (trimming) leather-hard pots on the wheel, as Binns taught it: soft steel tools the potter bends and files to shape, a turning stick and upright board to steady the hand, and wooden ribs cut to the shape of the inside of a pot. Result: a set of turning tools, a turning stick and board, and ribs. Source: C. F. Binns, The Potter's Craft (1910), pp. 86-88 and 179. Unknown: the tool sizes. Picture: Fig. 19 of the book.
Początkujący
Unknown

Instrukcje

1

Bend and file the turning tools

Make the turning tools of soft steel strip: bend each near its end and file the edge to suit. Make broad tools filed to a curve, for finishing concave surfaces; one or two narrow tools with a curved edge, which cut faster; and a small square tool. Keep the filing at its own bench so steel dust does not get into the clay. Ours: mild steel flat bar. Not given: the strip sizes.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 turning tools

Potrzebne narzędzia:

Piła do metaluPiła do metalu
MłotekMłotek
KowadłoKowadło
Pilnik do metaluPilnik do metalu
2

Make the board and turning stick

Cut a soft pine board 8 or 10 inches wide and 2 feet high, to stand upright at the back of the wheel frame opposite the potter, screwed on or set in a socket so it can be removed. Make the turning stick from a broomstick with a sharpened nail in its end; its point presses into the board at any height and the hand holding the tool rests on it, like a painter's mahl-stick. Ours: a wooden dowel for the broomstick.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 board support
Kołek drewnianyKołek drewniany1 turning stick
Gwoździe żelazneGwoździe żelazne1 stick point

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilnik do metaluPilnik do metalu
MłotekMłotek
3

Cut the ribs

Cut a piece of wood, called a rib, to the exact shape of the inside of the pot to be made; it smooths the inside while the wheel turns. Make one for each shape. Ours: hardwood.

Materiały do tego kroku:

Deska z drewna twardegoDeska z drewna twardego1 ribs

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilnik do metaluPilnik do metalu

Materiały

5

Wymagane narzędzia

4

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...