Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It

N. B. Cooper of Gratis, Ohio, received US 28,970, dated 3 July 1860, for a device to work the old upright dasher churn more easily. A post beside the churn carries a long hand lever and, on an adjustable block, a shorter bar linked to the dasher handle. The two are joined so the bar moves faster than the lever; pressing the lever down drives the dasher into the cream, and an india-rubber spring lifts everything again, like a pump on a spring pole. The block slides to suit churns of any height. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days

Instrukcje

1

Why the bar d runs ahead of the lever

Wczytywanie notatnika Jupyter…
2

A churn worked against a spring, four months before

Cunningham's spring pole drives the dasher down. Cooper's rubber spring lifts it back up, and the hand drives it down.
3

Read US 28,970

"The labor of lifting and returning the ordinary churn dasher by the smooth vertical handle, is by my process, or that which my improvement introduces, changed to an easy downward pressure upon a nearly horizontal bar or handle, the parts returning upwardly to their place by the force of the spring which was easily overcome by the downward pressure."
4

Base B, churn A, cover C and dasher D

Screw a hardwood base 520 x 400 mm and stand the bucket on it, held by a few cleats round its foot, as the patent says. Cut an HDPE cover with a 28 mm hole in the middle. Make a dasher of two crossed hardwood boards 220 x 40 x 16 mm on a 25 mm hardwood handle long enough to stand 300 mm above the cover.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Płyta HDPEPłyta HDPE1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
5

Standard E with slot a and holes b; block c

Glue up a hardwood standard 60 x 40 mm, 800 tall, and frame it into the base behind the churn, 210 mm from its centre. Rout a slot a 18 mm wide through it from 480 to 700 mm up, and bore 10.4 mm holes b across it every 30 mm. Make a hardwood block c that slides in the slot with shoulders bearing on both faces, with a 10 mm stainless pin through a hole b to set its height, and a tail behind the standard for the spring k.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
6

Lever F, piece g, block i, bar d and links e, f

Cut a hardwood lever F 28 x 16 mm, 810 long, and a piece g 340 long. Pivot both on a 10 mm stainless pin through a hole b 620 mm up, F on one face of the standard and g on the other, 110 mm of each behind it, and join them there with a pin j. At the churn's centre join them with a hardwood block i with a 28 mm upright hole for the dasher handle. Cut a hardwood bar d 24 x 16 mm, pivot it on the block c 55 mm from its back end, and join its back end to the pin j with two mild steel flat bar links f, 71 mm between holes. Join d's front end, 170 mm out, to the dasher handle with a flat bar link e 80 mm long hanging down to a pin m through the handle; bore the hole m where the dasher rests on the bottom with the levers level.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Śruba zamkowaŚruba zamkowa4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk
ZawleczkaZawleczka4 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
7

Springs k and l

Loop a length of elastic cord round the pin j and tie both ends to the block c's tail, tight enough to lift the lever and dasher when let go: the spring k. Tie a shorter loop from the bar d to the lever F as the spring l.

Materiały do tego kroku:

Sznurek elastycznySznurek elastyczny1 sztuka

Potrzebne narzędzia:

Miara zwijanaMiara zwijana
8

The build in 3D

FreeCAD model of this build, the churn cut open: the standard with its slot and holes, the block c, the lever F and piece g with the block i round the dasher handle, the bar d with links e and f, the rubber springs, and the dasher.
Plik projektowyBLENDCC0 - Free
9

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the churn and put on the cover. Set the block c so a full press of the handle brings the dasher near the bottom and the spring lifts it clear of the cream. Press the handle down and let it rise, steadily, timing it. When the butter comes, unpin the link e, lift out the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
10

Troubleshooting

Spring-lever churn troubleshooting.

Flow

Loading...
11

History and honest limits

**N. B. Cooper** of Gratis, Preble County, Ohio, US 28,970, 3 July 1860, "Churn". He claimed the mechanism of base, upright, block, hand lever, pivoted bar, links and springs together, to make the old dasher churn lighter work, likening it to a pump on a "spring pole". His springs are india rubber; ours are elastic cord. Every size here is ours.

Materiały

15

Wymagane narzędzia

18

Pliki projektowe

1

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...