Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Spiral-Wing Spheroid Churn: A Ball Dasher on Balls Turns Freely on Its Rod, Its Spiral Wings Spinning It Each Stroke
Otis W. Stanford of Cincinnati received US 28,696, dated 12 June 1860, for a churn. On the foot of an ordinary up-and-down dash rod he hangs a round or egg-shaped wooden dasher that turns freely on balls, with spiral wings nearly touching the tub's sides. As the rod is worked, the cream spins the dasher one way then the other; the cream is squeezed between the wings and the wall, and air trapped under the round body is carried into it.
The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 1 day, plus printing
Instrukcje
1
1
How far the dasher turns each stroke
How far the dasher turns each stroke
Wczytywanie notatnika Jupyter…
2
2
A dash that turns as it is driven, one week before
A dash that turns as it is driven, one week before
Ross's pitched blades turn the dash and handle on a swivel. Stanford's spiral wings turn the dasher alone, on balls.
3
3
Read US 28,696
Read US 28,696
"The rod C being reciprocated, as in the common churn, the inertia of the fluid acts to swiftly rotate the dasher in successively opposite directions and this reacting upon the liquid imparts to the latter a quick succession of opposite vertical movements resulting in violent agitation."
4
4
Print the dasher's upper half
Print the dasher's upper half
Upper half of the spheroid, 150 mm across and 80 tall, with the upper halves of three spiral wings reaching 116 mm; bored 12.8 mm with a 32 mm recess for the upper ring of balls. PETG, 0.2 mm layers, 30 % infill, 4 walls.
5
5
Print the dasher's lower half
Print the dasher's lower half
Lower half, printed upside down, with the lower halves of the wings and the recess for the lower ring of balls. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Lid B with boss b
Lid B with boss b
Turn a hardwood lid to fit the bucket's rim, 20 mm thick, with a boss 60 mm across and 140 mm tall in the middle, bored 26 mm through as the guide for the rod.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Klej do drewna1 sztukaPotrzebne narzędzia:
Tokarka do drewna
Zestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowa
Papier ścierny7
7
Rod C, dasher D, balls G, screw E and washer F
Rod C, dasher D, balls G, screw E and washer F
Cut a 25 mm hardwood rod 500 mm long and glue a 12 mm stainless spindle 170 mm long into its foot. Glue the two printed halves together with the wings lined up. Slide on a ring of 6 mm stainless balls in the upper recess, the dasher, and a second ring in the lower recess, and hold them with a stainless washer and a machine screw into the spindle's end. The dasher must spin freely.
Materiały do tego kroku:
Kołki z twardego drewna1 sztuka
Pręt ze stali nierdzewnej1 sztuka
Klej do drewna1 sztuka
Łożyska kulkowe20 sztuk
Śruby maszynowe1 sztuka
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Piła do metalu
Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wkrętaków8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket and lid cut open: the rod through the boss, the spheroid dasher with its three spiral wings on its two rings of balls, held by the washer.
9
9
Churn
Churn
Pour about 6 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dasher in and put on the lid over the rod. Work the rod up and down about 150 mm, steadily, timing it; the dasher turns one way and back. When the butter comes, lift the lid and dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka6 l
Sól morska gruboziarnista1 sztuka
Woda1 sztuka
Wiadro 20-litrowe1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej10
10
Troubleshooting
Troubleshooting
Spiral-wing dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Otis W. Stanford** of Cincinnati, Hamilton County, Ohio, US 28,696, 12 June 1860, "Churn". He claimed the upright tub with the reciprocating rod, the spheroidal dasher and spiral wings fitting the tub. His dasher is wooden; ours is printed in two halves, and the wings' number, twist and every size are ours.
Materiały
11- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 20 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
13- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
3Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Balance-Wheel Churn Frame: A Weighted Wheel Drives the Dash Up and Down and Its Pitched Blades Make It Revolve
autor: Buttercup
Obróbka drewna
5
0
0
0
0
0

Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It
autor: Buttercup
Obróbka drewna
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

