Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Diagonal-Blade Shouldered-Breaker Churn: Pitched Blades on Uneven Arms Turn Under the Shoulders of Two Breakers
Buttercup

Autor

Buttercup

11. listopad 2026IE
5
0
0
0
0

Diagonal-Blade Shouldered-Breaker Churn: Pitched Blades on Uneven Arms Turn Under the Shoulders of Two Breakers

Lester Day of Buffalo, New York, received US 26,970, dated 31 January 1860, for a churn. An upright shaft carries short upper arms and long lower arms, each with a rectangular blade set diagonally and adjustable along it, the two of a pair at different distances so neither follows the other's track. Two breakers, joined at the top and lifting out together, stand opposite each other with stepped shoulders under which the blades turn, and holes the cream is thrown through. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

Blades that never follow each other's track

Wczytywanie notatnika Jupyter…
2

Short blades within, a long one under, two months before

Jebb's thick staves are part of the tub. Day's breakers stand free, step back in two shoulders, and lift out.
3

Read US 26,970

"Motion being given to the dash blades by means of the crank and gearing, in the direction of the arrows, they will by their diagonal position on the arms throw the cream or milk outward against the side of the barrel and against the breakers, part passing through the space between the breakers and the side of the barrel, and part being thrown through the holes (h) in the breakers and part being thrown back by the breakers meeting these currents causing a concussion between them"
4

Print the wheel J

Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion I

Spur pinion, 12 teeth, module 2, with a 12.4 mm square socket for the shaft's top. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the foot step b

A cup 60 mm across and 25 mm tall with a 21 mm socket for the shaft's foot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Tub A, breakers E and cross piece F

Use a wooden tub 360 mm across inside and 450 mm deep; glue the foot step in the middle of its floor and two hardwood sockets g opposite each other against the wall. Cut two breakers from 15 mm hardwood, 420 mm tall, their outer edges 10 mm off the wall: from the top down to 350 mm up their inner edges reach 40 mm from the middle, then step out at H to 118 mm, and at H' (165 mm up) to 150 mm. Bore two 30 mm holes h through each at 220 and 290 mm up. Screw a cross piece 336 x 40 x 20 mm across their tops, bored 32 mm in the middle, and stand them in the sockets leaning slightly. Fill the tub with water overnight so it swells tight, then empty it.

Materiały do tego kroku:

Drewniana baliaDrewniana balia1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
WyrzynarkaWyrzynarka
Pilarka stołowaPilarka stołowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Miara zwijanaMiara zwijana
WodaWoda
8

Shaft B, arms C and blades D

Turn a hardwood shaft 30 mm across and 500 mm long, its foot turned to 19 mm and its top 40 mm cut to a 12 mm square. Bore it across for two 16 mm hardwood arms at 300 mm up, 204 mm long, and two at 110 mm up at right angles, 272 mm long. Cut eight blades 90 x 70 x 10 mm, bore each through its middle at 45 degrees to its face for the arm, and slide them on: the upper pair at 50 and 62 mm from the shaft, the lower at 84 and 96 mm, the nearer and farther blade on opposite sides. Pin each where it sits.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna2 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Papier ściernyPapier ścierny
Miara zwijanaMiara zwijana
9

Cover L, gear frame K and crank M

Cut a cover to sit on the rim, bored 32 mm in its middle, held by two hooks and eyes. Screw two chairs on it in a line from the middle, carrying a 12 mm stainless shaft with the crown wheel and a crank, and drop the pinion over the shaft's square top so they mesh. Lift the cover off to free the shaft; lift the breakers out by the cross piece to clean them.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
HaftkaHaftka2 sztuk
Wkręty do drewnaWkręty do drewna8 sztuk
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
KompasKompas
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Zestaw wkrętakówZestaw wkrętaków
10

The build in 3D

FreeCAD model of this build, the tub and cover cut through the middle: the two shouldered breakers with their holes and cross piece, the shaft with its short upper and long lower arms and diagonal blades, the foot step, and the crown wheel, pinion and crank on the cover. The dash was turned through 24 positions.
Plik projektowyBLENDCC0 - Free
11

Churn

Pour about 15 litres of heavy cream at about 15 °C into the tub, checked with the thermometer, put the cover on and hook it. Turn the crank steadily in the blades' direction, timing it. When the butter comes, lift the cover, dash and breakers out, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka15 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
12

Troubleshooting

Shouldered-breaker churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Lester Day** of Buffalo, Erie County, New York, US 26,970, 31 January 1860, "Churn". He claimed the breakers E with shoulders H, H', fixed to the cross piece F and removable with it, and the adjustable diagonal dash blades D working with them. His blades may also be turned on their arms to throw the cream upward, or inward and downward when reversed. His bevel wheel and pinion are here a printed crown wheel and pinion. The patent gives no sizes; every size here is ours.

Materiały

11

Wymagane narzędzia

19

Pliki projektowe

4

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...