Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream
Buttercup

Autor

Buttercup

11. listopad 2026IE
5
0
0
0
0

Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream

Daniel Deshon 2d of Somerset, Pennsylvania, received US 27,701, dated 3 April 1860, for a churn. A box of cream stands on curved rockers whose pegs sit in notches along the ways of a stand. Rocked by a handle, the box tips end to end and the cream runs through racks of rods; as the rockers roll, the point they rest on moves along with the weight, so little force is needed. The patent gives no sizes; every size here is ours, and so is our reading of where the racks sit.
Średniozaawansowany
About 2 days

Instrukcje

1

A fulcrum that walks

Wczytywanie notatnika Jupyter…
2

Cream rushing end to end through pins, one month before

Newbrough's barrel tips on a fixed pivot. Deshon's box rolls, so its pivot follows the cream.
3

Read US 27,701

"... this is done without contending but very little with the weight from the fact that the fulcrum at the bottom of the rockers (b) changes from one end to the other in accordance to the change of the weight inside of the vessel, always keeping in the center of the weight; consequently balancing the weight in its motion and saving most of the labor required to churn."
4

Vessel a and lid d

From 20 mm hardwood board make a box 600 x 250 mm inside and 290 deep; glue and screw it and seal the inside joints with silicone sealant. Cut a 150 mm opening across the middle of the top and a lid to fit it, with a hardwood block handle e.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna40 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
5

Racks i

Make two racks, each two hardwood side bars 24 x 20 mm, 355 long, with nine 10 mm stainless rods across between them. Stand them in the vessel leaning together, their feet on the floor 30 mm from the ends, meeting in the middle 240 mm above the floor.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
6

Rockers b with projections f, and handle c

Draw an arc of 400 mm radius with the compass on two 20 mm hardwood boards and cut each rocker with that arc as its bottom, 48 degrees of arc (325 mm), rising to the box's top; leave one 140 mm taller and cut a hand-hole in it as the handle c. Bore seven 12 mm holes along each arc, 6 degrees apart, and glue in dowel pegs standing 8 mm out as the projections f. Bolt a rocker on each long side of the vessel, centred, the arc's lowest point 40 mm below the vessel's bottom.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Śruba zamkowaŚruba zamkowa4 sztuk
Nakrętka skrzydełkowaNakrętka skrzydełkowa4 sztuk

Potrzebne narzędzia:

KompasKompas
WyrzynarkaWyrzynarka
KątomierzKątomierz
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Papier ściernyPapier ścierny
Klucz nastawnyKlucz nastawny
7

Pedestal h with ways and notches g

Cut two hardwood ways 520 x 120 x 30 mm and set them on edge under the rockers, 290 mm apart inside; join them with two cross boards near the floor. Cut seven notches 14 mm wide and 11 deep in each way's top edge, 41.9 mm apart from the middle, to match the pegs.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna16 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
8

The build in 3D

FreeCAD model of this build, tipped 10 degrees and cut through the middle: the vessel with its lid and the two racks leaning together, the rockers with their pegs in the ways' notches, and the pedestal.
Plik projektowyBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the vessel and close the lid. Push and pull the handle c steadily, tipping the vessel up to about 18 degrees each way, timing it. When the butter comes, lift the lid, take out the racks and the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka10 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
10

Troubleshooting

Rolling-rocker churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel Deshon 2d** of Somerset, Pennsylvania, US 27,701, 3 April 1860, "Churn". He claimed the racks, vessel, pedestal and rockers with projections in notched ways, combined. He places the racks only by dotted lines in his figure; our two racks leaning together are our reading of them. Every size here is ours.

Materiały

11

Wymagane narzędzia

19

Pliki projektowe

1

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...