Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End
Pearson Embree of West Chester, Pennsylvania, received US 27,536, dated 20 March 1860, for a churn. Inside a common barrel churn turned by a crank, rows of wooden slats about a quarter of the diameter high point obliquely to the barrel's motion, each row the opposite way to the last. Some throw the cream toward one end, some toward the other; it strikes other slats or the projections on the heads and turns back.
The slats' height follows the patent's proportion; every other size here is ours.
Średniozaawansowany
About 2 days
Instrukcje
1
1
Slats a quarter of the diameter high
Slats a quarter of the diameter high
Wczytywanie notatnika Jupyter…
2
2
Cream thrown end to end, two weeks before
Cream thrown end to end, two weeks before
Newbrough rocks his barrel so the cream runs end to end through pins. Embree turns his, and oblique slats throw it.
3
3
Read US 27,536
Read US 27,536
"The slats A A A, etc., throw the cream toward an end of the churn (one portion of the slats throwing to one end and the remaining portion to the other end); as the cream is thrown violently toward the end it either strikes other slats, or the projections B B by either of which means its course is reversed and great agitation of the cream produced."
4
4
Barrel, heads and door
Barrel, heads and door
Cut 430 mm of food-grade PE pipe 315 mm across with a 12 mm wall. Cut two heads from 15 mm HDPE sheet to fit inside it and bore both 20 mm on the centre. Cut a door 200 x 120 mm in the pipe's side, between two rows of slats; keep the piece, screw two HDPE strips along its long edges so it rests on the pipe, and hold it with two hooks and eyes.
Materiały do tego kroku:
Rura z polietylenu wysokiej gęstości1 sztuka
Płyta HDPE1 sztuka
Haftka2 sztuk
Śruby maszynowe4 sztuk
Nakrętka samohamowna z wkładką nylonową4 sztukPotrzebne narzędzia:
Wyrzynarka
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Pilniki (pilnik ręczny)
Zestaw wkrętaków
Miara zwijana5
5
Slats A, A', A'', A''' and projections B
Slats A, A', A'', A''' and projections B
Cut four hardwood strips 30 x 18 mm, 390 long, and sixteen hardwood slats 90 x 12 mm standing 73 mm from the barrel's wall, a quarter of its 291 mm inside diameter; round their ends if you like. Set four slats in each strip, 100 mm apart, each at 45 degrees to the strip: in the first and third strips one way, in the second and fourth the other. Screw the strips inside the barrel a quarter turn apart, through the wall with stainless screws and lock nuts, sealed with silicone, so each row points the opposite way from the row before. Screw two hardwood projections B, 20 x 90 mm and 30 deep, on each head's inner face, opposite each other, between the rows.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Klej do drewna1 sztuka
Śruby maszynowe16 sztuk
Nakrętka samohamowna z wkładką nylonową16 sztuk
Wkręty do drewna8 sztukPotrzebne narzędzia:
Pilarka stołowa
Kątomierz
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Ścisk stolarski listwowy
Papier ścierny
Zestaw wkrętaków
Klucz nastawny6
6
Shaft, stand and crank
Shaft, stand and crank
Pass a 20 mm stainless shaft 680 mm long through both heads, press the heads into the pipe's ends, screw them through the wall and seal the heads and the shaft's passages with silicone sealant. Make a hardwood stand: a base 600 x 400 mm and two uprights 40 x 120 mm, 30 mm beyond each end of the barrel, bored 20.8 mm 260 mm above the floor. Rest the shaft in them with collars, and fit a hardwood crank 130 mm long with a dowel handle on its long end.
Materiały do tego kroku:
Pręt ze stali nierdzewnej1 sztuka
Śruby maszynowe8 sztuk
Deska z drewna liściastego2 sztuk
Klej do drewna1 sztuka
Wkręty do drewna8 sztuk
Shaft Collar2 sztuk
Kołki z twardego drewna1 sztukaPotrzebne narzędzia:
Piła do metalu
Pilniki (pilnik ręczny)
Pilarka stołowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Zestaw wkrętaków7
7
The build in 3D
The build in 3D
FreeCAD model of this build, the barrel cut through the middle: four rows of oblique slats, alternate rows pointing opposite ways, the projections B on the heads, the door, the shaft, stand and crank.
8
8
Churn
Churn
Turn the door uppermost, pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it. When the butter comes, stop with the door uppermost, open it, tip the buttermilk out into a bowl, take out the butter, wash it in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka8 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej9
9
Troubleshooting
Troubleshooting
Oblique-slat barrel churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Pearson Embree** of West Chester, Chester County, Pennsylvania, US 27,536, 20 March 1860, "Churn". He claimed the slats or projections on the inner surface, each row pointing obliquely in the line of motion and the next row the opposite way. He says they make butter "in much less time than by the ordinary revolving churns". The slat height follows his quarter-diameter; the PE barrel, the 45-degree angle, the counts and all other sizes are ours.
Materiały
15- Zastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 28 sztukZastępnik
- Zastępnik
- 2 sztukZastępnik
- 2 sztukZastępnik
- 2 sztukZastępnik
- 16 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
17- 1 vendor sell this, none ship to you yetZastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
1Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Rocking Barrel Brake-Pin Churn: Cream Rushes End to End Through Rows of Pins, a Diagonal Board Gathers the Butter
autor: Buttercup
Obróbka drewna
7
0
0
0
0
0

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

