Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Bellows-and-Float Atmospheric Churn: Blasts of Air Through a Water-Jointed Pipe, a Float Gathers the Butter
Patrick S. Devlan of Reading, Pennsylvania, received US 24,382, dated 14 June 1859, for a churn worked by blasts of air only. A bellows under the body, worked by a lever, blows up a pipe that opens inside a wider tube; the air goes down between them and out through a perforated disk across the bottom, so it is spread through the whole cream. The cream standing in the tube makes a water joint, so no valves are needed. A perforated float with projections rides up and down on the bubbling cream and gathers the butter as it forms.
This rung builds it with a 20-litre bucket on legs and a bellows below.
Średniozaawansowany
About 1 day, plus printing
Instrukcje
1
1
The water joint
The water joint
Wczytywanie notatnika Jupyter…
2
2
Air drawn into the cream, before it
Air drawn into the cream, before it
Wicks drew air in with turning funnels and a dasher. Devlan blows it in with a bellows and has no dasher at all.
3
3
Read US 24,382
Read US 24,382
"... this pipe or tube, C, is open at its upper end, but is entirely surrounded to within a short distance of its base by another tube D, of greater diameter which tube D, is connected at its base to the center of the convex perforated disk d."
4
4
Print the teat e
Print the teat e
The hollow teat for the lid's middle, over tube D's top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
5
5
Print the collar
Print the collar
The collar that seals tube D into the disk's middle. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
6
6
Stand and bellows
Stand and bellows
Cut three legs a from 44 mm square timber 650 mm long and set them 120 degrees apart round a 350 mm circle. Screw a plywood seat ring 400 mm across, with a 60 mm hole, between them 482 mm up to carry the bucket, a band 600 mm up round the bucket, and a plywood shelf 150 mm up for the bellows. Screw a bellows about 260 x 120 mm to the shelf.
Materiały do tego kroku:
Drewno iglaste 70x70 mm2 sztuk
Płyta sklejkowa2 sztuk
Wkręty do drewna24 sztuk
Klej do drewna1 sztuka
Miech1 sztukaPotrzebne narzędzia:
Piła ręczna
Wyrzynarka
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Miara zwijana7
7
Pipe C, tube D and disk d
Pipe C, tube D and disk d
Drill the middle of the bucket's floor 16.5 mm and seal a 16 mm stainless pipe C through it with silicone so it stands 400 mm up. Drill 24 holes of 4 mm in two rings in a stainless bowl about 260 mm across and a 32.5 mm hole in its middle, and stand it upside down on the floor round the pipe as disk d. Push a 32 mm stainless tube D 360 mm long through the printed collar into the bowl's middle hole, sealed with silicone, so it surrounds pipe C down to 56 mm above the floor. Run silicone tubing from the bellows' nozzle to pipe C's foot under the floor.
Materiały do tego kroku:
Wiadro 20-litrowe1 sztuka
Rura ze stali nierdzewnej2 sztuk
Duża misa ze stali nierdzewnej1 sztuka
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw otwornic
Obcinak do rur
Pilniki (pilnik ręczny)8
8
Lid, float and lever
Lid, float and lever
Cut a 45 mm hole in the middle of the bucket's lid and glue the teat e over it, with its cap f. Cut float G from 15 mm plywood, 250 mm across with a 48 mm hole for tube D and eight 22 mm holes, and glue 10 mm dowel pegs 25 mm long into both faces as the projections g. Bolt a hardwood lever b to the outside of one leg 360 mm up, running up beside the bucket to a handle c above the lid, and join it to the bellows' top board with a hardwood link.
Materiały do tego kroku:
Filament PETG1 sztuka
Klej do drewna1 sztuka
Płyta sklejkowa1 sztuka
Kołki z twardego drewna1 sztuka
Deska z drewna liściastego2 sztuk
Zestaw śrub sześciokątnych3 sztuk
Podkładka płaska6 sztuk
Nakrętka samohamowna z wkładką nylonową3 sztukPotrzebne narzędzia:
Zestaw otwornic
Wyrzynarka
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Piła ręczna
Papier ścierny
Klucz nastawny9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the near half of the body cut away: the stand with its seat, band and shelf, the bellows and hose, pipe C inside tube D, the drilled bowl as disk d, the float with its pegs, the lid with its teat and cover, and the lever with its link.
10
10
Churn
Churn
Fill the bucket about one third full: about 6.5 litres of heavy cream at about 15 °C, checked with the thermometer. Drop the float in over tube D and put the lid on. Work the lever steadily and time it: each stroke blows a burst of air up the pipe, down the tube and out through the bowl's holes. When the butter has gathered on the float, lift it out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka6.5 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej11
11
Troubleshooting
Troubleshooting
Atmospheric churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Patrick S. Devlan** of Reading, Berks County, Pennsylvania (the drawing spells it Devlen), US 24,382, 14 June 1859. Earlier blast churns, he wrote, blew the air in one place, needed valves and did not collect the butter; he claimed the float in a churn worked by blast only. His only quantity is "say one third full". His pipe C rises straight from the bellows and his disk d spans the floor; our hose, drilled bowl, pegs and every size are ours.
Materiały
19- 2 sztukZastępnik
- 2 sztukZastępnik
- 24 sztukZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 3 sztukZastępnik
- 6 sztukZastępnik
- Zastępnik
- 6.5 lZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
15- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
3Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Funnel-Tube Atmospheric Churn: Trailing Funnels on a Fast Cross Draw Air Down Slanting Tubes Into the Cream
autor: Buttercup
JEDZENIE I NAPOJE
4
0
0
0
0
0

Fan-Blown Jet Dasher Churn: A Fan on the Crank Shaft Blows Air Out Through the Dasher Below the Cream
autor: Buttercup
JEDZENIE I NAPOJE
42
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

