Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Nested Hollow-Dasher Churn: Two Dasher Frames Turn Contrary Ways, Their Hollowed Side Pieces Driving Cream at Webs
Buttercup

Autor

Buttercup

11. listopad 2026IE
8
0
0
0
0

Nested Hollow-Dasher Churn: Two Dasher Frames Turn Contrary Ways, Their Hollowed Side Pieces Driving Cream at Webs

Stephen P. Dunham and Austin Hipple of Kilbourne, Ohio, received US 27,894, dated 17 April 1860, for a churn. One dasher frame turns inside another, the two driven contrary ways by one winch through a face-toothed wheel and two pinions. The side pieces of each frame are hollowed on their leading edges and throw the cream at thin webs: the outer frame's at webs on the vessel's wall, the inner frame's at webs on the outer frame. The patent gives no sizes; every size here is ours.
Zaawansowany
About 3 days, plus printing

Instrukcje

1

One wheel, two pinions, two directions

Wczytywanie notatnika Jupyter…
2

Contrary turning from toothed faces, two months before

Ward turns a cylinder against its dashers. Dunham and Hipple turn one dasher frame inside another.
3

Read US 27,894

"The cream is projected by the surfaces of the hollow s, c, onto the wall of the vessel, by which it is constrained to take up a circular motion till obstructed by the webs, a, and reflected by them in currents, toward the middle of the vessel, and with a velocity increasing as the distances between these hollows and webs diminish."
4

Print the driving wheel D

Face-toothed wheel, 36 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion F

Spur pinion, 16 teeth, module 2, with a hub; bored 18.4 mm for the hollow arbor. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the pinion E

Spur pinion, 16 teeth, module 2, with a hub; bored 12.4 mm for the shaft S. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Webs a, step r and pivot bolt e

Screw four hardwood webs 4 mm thick and 10 deep upright inside the bucket a quarter turn apart, from the floor to 310 mm up, sealing the screw holes outside with silicone. Screw a hardwood block 50 x 50 x 8 mm to the floor's centre as the step r and bore it 12.6 mm, 6 deep. Cut a 12 mm stainless rod 60 mm long as the pivot bolt e.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Wkręty do drewnaWkręty do drewna10 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Zestaw wkrętakówZestaw wkrętaków
8

Outer dasher with hollows c and webs b

Halve together two hardwood arms 30 x 30 mm, 240 long, for the top and two for the bottom, crossed. Cut four side pieces 20 x 42 mm, 295 long, and join the arms' ends top and bottom with them, 310 mm overall. Hollow each side piece's outer edge on the same side, 12 mm deep at the middle and running out near the ends. Glue a hardwood web b, 4 x 11 mm, along each side piece's inner face. Bore the lower arms' crossing 12.6 mm for the pivot bolt and the upper arms' crossing 33 mm for the journal; fix an 18 mm stainless tube 102 mm long upright over the upper crossing as the hollow arbor.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna16 sztuk
Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
WyrzynarkaWyrzynarka
Papier ściernyPapier ścierny
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Piła do metaluPiła do metalu
Ścisk stolarski listwowyŚcisk stolarski listwowy
9

Inner dasher with hollows d and journal G

Make the inner dasher the same way from 25 mm hardwood: arms 164 mm long, four side pieces 18 x 34 mm, 195 overall, hollowed 10 mm deep on the opposite edge from the outer dasher's, no webs. Bore the lower arms' crossing 13 mm, 12 deep, for the pivot bolt. Turn a hardwood journal G 32 mm across and 55 tall with two lugs, cut a 12.4 mm square socket in its top, and screw it to the upper arms' crossing.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
WyrzynarkaWyrzynarka
Papier ściernyPapier ścierny
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
10

Cover B, shaft S and gearing

Set the inner dasher inside the outer, its journal up through the outer's upper arms, and stand both on the pivot bolt in the step. Cut a hardwood cover in two halves, 350 x 330 x 15 mm overall, with a 24 mm hole for the arbor; slide pinion F onto the arbor above it. File the bottom 40 mm of a 12 mm stainless shaft square to fit the journal's socket, pass it down through the arbor, and key pinion E on its top. On one half of the cover screw two hardwood standards carrying a 12 mm shaft H with wheel D meshing E above and F below, a hardwood winch I with a dowel handle, and a bracket over E holding the shaft's top.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Filament PETGFilament PETG1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Shaft CollarShaft Collar2 sztuk
ZawleczkaZawleczka1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the webs a, the outer dasher with hollowed side pieces and webs b, the inner dasher with its hollows and journal, the pivot bolt in its step, and the cover with the wheel D meshing pinion E above and pinion F below.
Plik projektowyBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dashers and the gearing in place, and turn the winch steadily, timing it, the way that brings each frame's hollows toward the webs ahead of them. When the butter comes, lift off the cover and gearing, lift out the dashers, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
13

Troubleshooting

Nested-dasher churn troubleshooting.

Flow

Loading...
14

History and honest limits

**Stephen P. Dunham** and **Austin Hipple** of Kilbourne, Delaware County, Ohio, US 27,894, 17 April 1860, "Churn". They did not claim a wheel geared with two pinions to turn dashers contrary ways, but the hollowed side pieces working with the webs on the vessel and on the outer dasher. Their vessel is conical, wider at the bottom; ours is a bucket. Every size here is ours, and our gears are printed.

Materiały

15

Wymagane narzędzia

17

Pliki projektowe

4

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...