Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
Edwin Ward of New York received US 27,175, dated 14 February 1860, for a churn. A horizontal cylinder with ribs inside turns on bearings while a shaft through it, carrying dashers, turns the other way: one crank drives both, the cylinder through a pair of pinions on a tube round a short fixed shaft and a toothed ring on its head. He reports butter "in from three to five minutes".
The patent gives no sizes; every size here is ours.
Zaawansowany
About 3 days, plus printing
Instrukcje
1
1
One crank, two directions
One crank, two directions
Wczytywanie notatnika Jupyter…
2
2
Dashers turning inside a still barrel, two months before
Dashers turning inside a still barrel, two months before
Rohrer's barrel stands still round the turning dashers. Ward turns the cylinder too, the other way.
3
3
Read US 27,175
Read US 27,175
"Now it will readily be seen that whenever rotation is given to the shaft that it and the dashers will traverse in one direction and that the cylinder and slats will traverse in a contrary direction, and that the velocity of the one in relation to that of the other will depend upon the number of teeth and comparative diameter of the pinions and the toothed surface on the head of the cylinder."
4
4
Print the crown wheel j
Print the crown wheel j
Crown wheel, 60 teeth on its face, module 2, with a hub bored 16.4 mm for the shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the toothed ring o
Print the toothed ring o
Crown ring, 120 teeth on its face, module 2, 258 mm across, to screw to the cylinder's head. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pinions k and n
Print the pinions k and n
Spur pinion, 12 teeth, module 2, bored 12.6 mm to turn on the fixed shaft l. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Cylinder a with ribs d and door p
Cylinder a with ribs d and door p
Cut two hardwood heads 364 mm across from 25 mm board, each with a hub 50 mm across bored 17 mm on the axis, the geared head's hub 38 mm long. Bend 1.5 mm stainless sheet into a shell 360 mm across inside and 450 long, screw it to the heads with silicone sealant, and screw four hardwood ribs 30 x 30 mm, 450 long, inside it a quarter turn apart. Cut a door 140 x 160 mm in the shell, hung on two small hinges and closed with a hook. Screw the printed toothed ring to the geared head's face.
Materiały do tego kroku:
Deska z drewna liściastego2 sztuk
Blacha ze stali nierdzewnej2 sztuk
Wkręty do drewna40 sztuk
Śruby maszynowe8 sztuk
Zawias meblowy czopowy2 sztuk
Haftka1 sztukaPotrzebne narzędzia:
Kompas
Wyrzynarka
Frezarka górnowrzecionowa
Nożyce do blachy
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Ścisk stolarski listwowy
Zestaw wkrętaków8
8
Shaft f, dashers g and crank h
Shaft f, dashers g and crank h
Cut a 16 mm stainless shaft 662 mm long. Screw four hardwood dashers 430 x 122 x 16 mm to hardwood blocks pinned on it, a quarter turn apart, reaching 140 mm from the axis, and pass it through the heads' hubs. Fit the crown wheel on the geared end and a crank 160 mm long with a handle beyond it.
Materiały do tego kroku:
Pręt ze stali nierdzewnej1 sztuka
Deska z drewna liściastego1 sztuka
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztuka
Shaft Collar2 sztuk
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Pilarka stołowa
Piła do metalu
Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Papier ścierny9
9
Frame c, bearings b, fixed shaft l and standard m
Frame c, bearings b, fixed shaft l and standard m
On a base board stand a post with a hardwood bearing block bored 51 mm for the plain head's hub. At the geared end stand a hardwood standard m, and fix a 12 mm stainless rod l upright in its top, running up into a second bearing block for the geared hub just outside the toothed ring. On l, below the shaft, slide the two pinions joined by a short stainless tube: the upper one meshing the crown wheel j, the lower the toothed ring o. Hold them with collars.
Materiały do tego kroku:
Drewno iglaste 70x70 mm1 sztuka
Deska z drewna liściastego2 sztuk
Pręt ze stali nierdzewnej1 sztuka
Rura ze stali nierdzewnej1 sztuka
Shaft Collar2 sztuk
Zestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonową4 sztukPotrzebne narzędzia:
Pilarka stołowa
Zestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Piła do metalu
Klucz nastawny
Miara zwijana10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the cylinder cut through the middle: the ribs and four dashers, the shaft and crank, the crown wheel and toothed ring facing each other across the upright fixed shaft with its two pinions, the bearings, post and standard on the base.
11
11
Churn
Churn
Turn the door uppermost, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it: the patent says three to five minutes. When the butter comes, turn the door down over a bowl, let the buttermilk run out, take out the butter, wash it in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka12 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej12
12
Troubleshooting
Troubleshooting
Counter-turning churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Edwin Ward** of New York, US 27,175, 14 February 1860, "Churn". He claimed the horizontal cylinder with ribs and an interior shaft with dashers, made to turn in opposite directions. His bevel pinions and the toothed surface on the head are here printed crown gears and pinions, and his fixed shaft l is upright, carrying the geared end's bearing. The patent gives no sizes; every size here is ours.
Materiały
19- 2 sztukZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 40 sztukZastępnik
- 8 sztukZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 4 sztukZastępnik
- Zastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
20- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
4Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Diagonal-Blade Shouldered-Breaker Churn: Pitched Blades on Uneven Arms Turn Under the Shoulders of Two Breakers
autor: Buttercup
Obróbka drewna
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

