Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman
Buttercup

Autor

Buttercup

11. listopad 2026IE
7
0
0
0
0

Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman

J. W. Evans of Forsyth, Georgia, received US 28,462, dated 29 May 1860, for a frame on legs that stands over an ordinary churn. A hand crank turns a cogged wheel and a pinion, whose crank works a pitman and a sliding sash; the dasher is held in the sash by a set screw, so it is put in or taken out in a moment, and makes several strokes to each turn of the handle. The dasher is a grated one. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

Several strokes to one turn

Wczytywanie notatnika Jupyter…
2

More strokes than turns, three months before

Clement gets two strokes a turn from a toggle. Evans gears his crank up for four.
3

Read US 28,462

"The nature of my invention consists in providing a frame with suitable gearing to communicate a reciprocating motion to which the dasher of an ordinary churn can be attached or detached with facility, the whole forming a churn which can be worked to great advantage by a laborer by means of a crank."
4

Print the grated dasher h

Disc 200 mm across and 10 thick with seven slots 14 mm wide, a rim and a cross bar. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the cogged wheel w

Spur gear, module 2.5, 48 teeth, 12 mm wide, with a hub; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the pinion p

Spur pinion, module 2.5, 12 teeth, 12 mm wide, with a hub; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Frame A and legs L

From pine lumber 40 x 80 mm cut two uprights 570 mm long and a top bar 380 long, and join them 300 mm apart inside. Rout a groove 12 x 42 mm down the inside of each upright for the sash. Stand the frame on two rails and four legs 400 tall, the rails across the bucket's place so the frame stands over it. Screw a hardwood strap 60 x 20 mm upright behind the frame's middle, with a cross piece near its foot, and bore it 16.6 mm for the shafts c and d, 75 mm apart, 400 and 475 mm above the frame's foot.

Materiały do tego kroku:

Tarcica sosnowaTarcica sosnowa3 sztuk
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna30 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
8

Wheel w, pinion p, cranks k and d

Pass a 16 mm stainless shaft c through the upper hole with the wheel w on its front end and a hardwood crank k 140 mm long with a dowel handle on its back end. Pass a short 16 mm shaft through the lower hole with the pinion p meshing w, and in front of it a hardwood crank d with a 12 mm stainless pin 40 mm from the shaft. Hold both with collars.

Materiały do tego kroku:

Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Shaft CollarShaft Collar4 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Papier ściernyPapier ścierny
9

Pitman e, sash f and set screw i

Cut a hardwood pitman 20 x 10 mm with 12.6 mm holes 220 mm apart. Cut a hardwood sash 320 x 40 x 40 mm with tongues on its ends to slide in the grooves; bore it 22.6 mm through the middle for the dasher rod, slot its front for the pitman, and pin the pitman in the slot. Drill and tap a hole through the sash's back into the bore, or set a nut in it, and run in a short piece of threaded rod with a wing nut as the set screw i.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
ZawleczkaZawleczka2 sztuk
Pręt gwintowanyPręt gwintowany1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna1 sztuka
Nakrętka skrzydełkowaNakrętka skrzydełkowa1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Piła do metaluPiła do metalu
Klucz nastawnyKlucz nastawny
10

Dasher g with the grate h

Glue a 22 mm hardwood dowel 555 mm long into the printed grate's centre, and cut a 28 mm hole in the centre of the bucket's lid for it.

Materiały do tego kroku:

Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wiadro 20-litroweWiadro 20-litrowe1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the frame on its legs, the wheel w and pinion p behind the crank d, the pitman and the sash in its grooves, the dasher held by the set screw, and the grated dasher near the bucket's floor.
Plik projektowyBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on the lid. Stand the frame over it, pass the dasher down through the sash into the bucket, set it so it just clears the floor at the bottom of the stroke and tighten the set screw. Turn the crank k steadily, timing it. When the butter comes, loosen the set screw and lift the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
13

Troubleshooting

Geared crank-frame churn troubleshooting.

Flow

Loading...
14

History and honest limits

**J. W. Evans** of Forsyth, Monroe County, Georgia, US 28,462, 29 May 1860, "Churn". He did not claim churn dashers worked by a crank nor the grated dasher, "as they are old and well known", but the arrangement with the grated dasher, sash and set screw. His frame is arched and on curved legs, and his wheel and pinion are drawn face-toothed; ours are spur gears on a strap behind a straight frame. Every size is ours.

Materiały

16

Wymagane narzędzia

19

Pliki projektowe

4

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...