Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Rocking-Churns Water-Jacket Churn: Two Small Churns Rock and Their Dashers Plunge, Wings Turn Above
Samuel Gissinger of Allegheny, Pennsylvania, received US 25,502, dated 20 September 1859, for a churn. Inside a case with a water space under its bottom and sides, a lift-out frame holds two shafts. The upper one turns with wings on it and two cranks; from each crank a stem works a dasher inside a small churn hung on the lower shaft, so the dashers plunge while the churns and the wings between them rock. Warm or cold water in the jacket sets the cream's temperature.
The patent gives no sizes; every size here is ours. Its drawing shows the two dashers at different heights; with both churns fixed on one shaft that would bind, so here the cranks are in step.
Zaawansowany
About 3 days, plus printing
Instrukcje
1
1
How a stem rocks its churn
How a stem rocks its churn
Wczytywanie notatnika Jupyter…
2
2
A churn with a water chamber, a few weeks before
A churn with a water chamber, a few weeks before
Langdon's box turned round a fixed dash-frame. Gissinger's case stands still with water under and beside it, and the dashers work inside two small churns that rock.
3
3
Read US 25,502
Read US 25,502
"Having all things arranged as represented in Fig. 1 of the drawings, the milk or cream is put in the case (a), and warm or cold water as the case may require is put in the chamber (o) at pipe (r) the exit opening being closed with a suitable stopple. And now by turning crank (q) which will revolve the shaft (f) with its wings (g), and also operate the dashers (m) and give to the churns (i) and their wings (h) an oscillating motion"
4
4
Print the churns i
Print the churns i
A churn 120 mm across and 108 mm deep with a lug under its floor bored 12.6 mm for shaft j and a cross hole for a pin. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the dashers m
Print the dashers m
A disc 108 mm across and 8 mm thick with six 14 mm holes and a boss bored 8.4 mm for the stem. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the wings g
Print the wings g
A paddle 60 x 96 x 6 mm with three 20 mm holes on a split hub that clamps round the 12 mm shaft with two M4 screws. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Case a, chamber o, lid b
Case a, chamber o, lid b
From 20 mm hardwood make the inner case n 460 x 260 mm and 380 mm deep inside. Build the outer case round it with a 30 mm space under the bottom and along both long sides, sharing the two ends; set a spacer strip under the middle. Close the tops of the side spaces with strips, fit a short brass tube in one as the supply pipe r, and bore a hole low in the other side for a rubber stopper as the exit p. In one end cut a slot 26 mm wide from the top down to 217 mm for the crank shaft. Glue two strips 18 x 20 mm up the inside of each end, 124 mm apart, as the guides. Make the lid in two halves with a handle c on each. Fill the case and the chamber with water overnight so they swell tight, then empty them.
Materiały do tego kroku:
Deska z drewna liściastego5 sztuk
Klej do drewna1 sztuka
Wkręty do drewna40 sztuk
Rura mosiężna1 sztuka
Korki gumowe1 sztuka
Kołki z twardego drewna1 sztukaPotrzebne narzędzia:
Pilarka stołowa
Piła ręczna
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Dłuto do gniazd
Pobijak drewniany
Ścisk stolarski listwowy
Kątownik stolarski
Miara zwijana
Woda8
8
Frame e and the two shafts
Frame e and the two shafts
Cut two end plates 122 x 20 mm, 375 mm long, to stand between the guides, and bore each 12.8 mm at 230 mm and 40 mm up. Bend 12 mm stainless rod into the shaft f: two cranks of 40 mm throw, 280 mm apart and pointing the same way, each pin 30 mm long, heating each bend red with the torch; leave one end long enough to pass through the slot and bend it into the crank q, 130 mm long, with a hardwood handle. Cut shaft j from the same rod, 456 mm long.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnej2 sztuk
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztukaPotrzebne narzędzia:
Pilarka stołowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Palnik propanowy
Imadło warsztatowe
Młotek
Rękawice żaroodporne
Piła do metalu
Pilniki (pilnik ręczny)9
9
Churns, dashers, stems and wings
Churns, dashers, stems and wings
Pin the two churns on shaft j under the cranks, mouths up, and pin a hardwood wing h, 150 x 95 x 20 mm, on j between them. Cut two stems from 8 mm stainless rod, fix each in a dasher's boss, and bend its top into an eye round its crank pin so the pin sits 110 mm above the dasher, closing it with the torch and pliers. Clamp the two wings g on the shaft f between the cranks, pointing opposite ways. Put shafts f and j through the end plates and the dashers into the churns.
Materiały do tego kroku:
Pręt ze stali nierdzewnej1 sztuka
Deska z drewna liściastego1 sztuka
Śruby maszynowe4 sztuk
Nakrętka samohamowna z wkładką nylonową4 sztuk
Zawleczka6 sztuk
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Palnik propanowy
Imadło warsztatowe
Rękawice żaroodporne
Piła do metalu
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wkrętaków
Papier ścierny10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the case cut through its middle: the water space under and beside the inner case, the frame's end plates in their guides, the bent shaft f with its two cranks in step and its wings, the churns on shaft j with the wing between them, and the dashers on their stems. The crank was turned through 24 positions.
11
11
Churn
Churn
Stopper the exit and pour warm or cold water into the chamber through the pipe until the cream will sit at about 15 °C. Lower the frame into its guides, pour in about 22 litres of heavy cream, checking it with the thermometer, and put the lid on. Turn the crank steadily, timing it. When the butter comes, lift the frame out, gather the butter, drain the buttermilk and the chamber, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka22 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej12
12
Troubleshooting
Troubleshooting
Rocking-churns churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Samuel Gissinger** of Allegheny, Pennsylvania, US 25,502, 20 September 1859, "Churn". He claimed the arrangement in the movable frame e of the oscillating churns i with dashers m and wings h, in combination with the revolving shaft f and its wings g. The patent gives no sizes; every size here is ours. His Fig. 1 draws the two dashers at different heights, but both churns are "secured to the shaft (j)": cranks out of step would push them opposite ways and bind, so ours are in step. His case is rounded at the ends and the water chamber tapered; ours is square.
Materiały
14- 5 sztukZastępnik
- 2 sztukZastępnik
- 40 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 4 sztukZastępnik
- Zastępnik
- 6 sztukZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
24- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
4Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Twin-Crank Slide-Top Churn: Two Dashers on a Bent Crank Shaft, Sliding Plates Keep the Milk In
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter
autor: Buttercup
Obróbka drewna
11
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

