Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It
Buttercup

Autor

Buttercup

11. listopad 2026IE
5
0
0
0
0

Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It

W. B. Gordinier of Coudersport, Pennsylvania, received US 28,170, dated 8 May 1860, for a pendulum churn. The churn stands in a frame that hangs like a swing and is set swinging with a treadle and a cord over a pulley. Arms from the base hold the dash rod's cross head, so as the swing moves the dasher plunges up and down, while a twisted strip on the rod, working through a slotted bar, turns it back and forth. The patent gives no sizes; every size here is ours.
Zaawansowany
About 3 days

Instrukcje

1

Why the dasher plunges as the churn swings

Wczytywanie notatnika Jupyter…
2

A spiral that turns a push into a spin, one week before

Ashley slides a nut on a spiral to spin his beater. Gordinier slides his twisted strip through a slot.
3

Read US 28,170

"From this description it will be seen that the mechanism for operating the churn gives to the parts a combined vibrating, reciprocating, and alternate rotary motion, which are obtained by simply moving the treadle L."
4

Base A, standards B and cross bar B'

From pine lumber 60 x 50 mm make a base 1600 x 660 mm with four cross pieces, one under the pivot. Stand two standards 60 x 60 mm at the middle of the long sides, 1350 mm tall, joined at the top by a cross bar B'. Bore them 25 mm across 1300 mm above the floor for a 24 mm stainless pivot shaft, with the pulley J loose on its middle.

Materiały do tego kroku:

Tarcica sosnowaTarcica sosnowa4 sztuk
Wkręty do drewnaWkręty do drewna40 sztuk
Klej do drewnaKlej do drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
KrążekKrążek1 sztuka
Shaft CollarShaft Collar2 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
5

Swing frame C, cross bar H and churn box E

Hang two hardwood hangers 90 x 30 x 60 mm on the pivot shaft, 400 mm apart, and fix two 20 mm hardwood dowels upright under each, 60 mm apart centre to centre, reaching 1150 mm down to a hardwood bottom board 440 x 440 x 25 mm. Across the arms 400 mm below the pivot fix a hardwood bar H with a slot 28 x 7 mm in its middle. Screw a 20-litre bucket to the board and cut a 28 mm hole in its lid's centre.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Kołki z twardego drewnaKołki z twardego drewna4 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna16 sztuk
Wiadro 20-litroweWiadro 20-litrowe1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
6

Cross head D, dash rod D', strip G and arms F

Cut a hardwood cross head 28 x 40 mm, 504 long, notched at each end to run between a pair of arm rods, with a hardwood roller 36 mm across on a pin at each end. Bore its middle 21 mm. Cut a 20 mm stainless dash rod, cut a groove round it and hold it in the cross head with two key collars in the groove, so it turns; fix a hardwood dasher, two crossed boards 220 x 60 x 16 mm with four 20 mm holes, 410 mm below the cross head. Twist a stainless strip 25 x 3 mm, 300 long, a quarter turn every 90 mm in the vise, fix it to the rod's top and pass it up through bar H's slot. Cut two mild steel flat bar arms F with holes 640 mm apart; bolt one end of each to a bracket on the base under the pivot, 60 mm up, and the other to the cross head's end.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Shaft CollarShaft Collar2 sztuk
Blacha ze stali nierdzewnejBlacha ze stali nierdzewnej1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej2 sztuk
Śruba zamkowaŚruba zamkowa4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Piła do metaluPiła do metalu
Nożyce do blachyNożyce do blachy
Imadło warsztatoweImadło warsztatowe
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Klucz nastawnyKlucz nastawny
7

Treadle L and cord K

Hinge a hardwood treadle 600 x 240 x 25 mm to a block on the base beyond the churn. Tie a cord to each end of the cross head, bring both up to the pulley J, take them over it together and down to the treadle's far end.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Zawias meblowy czopowyZawias meblowy czopowy2 sztuk
Wkręty do drewnaWkręty do drewna8 sztuk
SznurekSznurek1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
8

The build in 3D

FreeCAD model of this build, swung 12 degrees: the base and standards, the swing frame with its bottom board and the bucket cut open, the cross head between the arm rods, the arms F from the base, the dash rod and dasher, the twisted strip through bar H, the pulley J on the pivot shaft, the cord and the treadle.
Plik projektowyBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on its lid. Work the treadle with your foot in time with the swing, timing it, so the churn swings up to about 20 degrees each way. When the butter comes, stop the swing, unbolt the arms F from the cross head and lift the dash rod out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka10 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
10

Troubleshooting

Pendulum churn troubleshooting.

Flow

Loading...
11

History and honest limits

**W. B. Gordinier** of Coudersport, Potter County, Pennsylvania, US 28,170, 8 May 1860, "Churn" (the drawing spells the name Gordnier). He claimed the swinging frame carrying the churn, with the arms F, spiral plate G, cord K, pulley J and treadle L. He does not explain how the arms make the dasher rise and fall; the working above is ours. Every size is ours.

Materiały

18

Wymagane narzędzia

17

Pliki projektowe

1

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...