Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Forge

Autor

Forge

13. listopad 2026NO
7
0
0
0
0

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)

Harry O. Hall of Murray, Utah, received US 1,930,168, dated 10 October 1933, for a portable saw table where the saw moves and the work stays still. The saw and its motor hang from a carriage under the top. The carriage rolls on balls in V-shaped tracks in a straight line. A foot lever pulls it back through a board held against the fence, and springs bring it forward again. Nuts on a hanging stem set the depth, and a spring under the motor keeps the belts tight. The table rolls on wheels and its back legs fold. The patent gives no sizes; every size here is ours, and our top is plywood where his is folded sheet metal.
Zaawansowany
About 1 week

Instrukcje

1

The foot lever, the travel and the cut

Wczytywanie notatnika Jupyter…
2

Read US 1,930,168

"The movable saw carriage is mounted to freely move longitudinally of the table in a straight line and is moved into engagement with the piece of work held in position by the work fence, when the lever 29' is depressed by the foot."
3

Table and legs

Make the top 5 of 18 mm plywood 1000 x 600 mm with pine aprons 6, 7 round it, and cut a slot 47 12 mm wide and 500 mm long down its middle. Fix four pine legs 9, 10 splayed outwards at the corners with braces 11 and plywood gussets 12, the top 850 mm high; bolt the rear legs' gussets with one bolt each as a pivot and a second removable bolt, so they fold. Put an axle 15 between the front legs with a wheel 14 on each end.

Materiały do tego kroku:

Płyta sklejkowaPłyta sklejkowa1 sztuka
Tarcica sosnowaTarcica sosnowa6 sztuk
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Zestaw kół gumowychZestaw kół gumowych1 sztuka
Śruba zamkowaŚruba zamkowa8 sztuk
Wkręty do drewnaWkręty do drewna40 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Kątownik nastawnyKątownik nastawny
Miara zwijanaMiara zwijana
4

Tracks and carriage

Screw a pine rail 22 along each side under the top and bolt a length of steel angle on it, V upwards, as the track 21. Make the carriage of two more angles 16, V downwards over the tracks, joined near each end by a cross bolt 17 with nuts 19 either side of each angle, so their spacing can be set. Under each end of each carriage angle, between the bolt and a small steel lug 23 bolted inside the angle, put a 10 mm steel ball 20 to roll in the track. Hook two springs 24 from the front wall of the top to the front cross bolt.

Materiały do tego kroku:

Tarcica sosnowaTarcica sosnowa1 sztuka
Kątownik ze stali miękkiejKątownik ze stali miękkiej2 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych12 sztuk
Pręt gwintowanyPręt gwintowany1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna8 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Łożyska kulkoweŁożyska kulkowe1 sztuka
Sprężyna naciągowaSprężyna naciągowa2 sztuk
Wkręty do drewnaWkręty do drewna16 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Szlifierka kątowaSzlifierka kątowa
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw pilnikówZestaw pilników
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
Okulary ochronneOkulary ochronne
5

Foot lever and chain

Pivot a hardwood foot lever 29' on the front axle, reaching back along the floor, with a pedal 31 on its free end. Fix a pulley 28 on a shaft 29 between the rear legs. Run a chain 27 from the rear cross bolt of the carriage over the pulley and down to the lever, fixed 450 mm from its pivot. Pressing the pedal pulls the carriage back; letting go, the springs return it.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
KrążekKrążek1 sztuka
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Łańcuch rolkowyŁańcuch rolkowy1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych3 sztuk

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Klucz nastawnyKlucz nastawny
6

Saw frame, arbor and shield

Bolt a rectangle of steel angle as the saw frame 32. Hang one end on the rear cross bolt between two collars 33 with set screws 34, so it can be slid sideways. On the front cross bolt put a sleeve 35 between collars 36 with a threaded stem 38 hanging from it, through a hole 39 in the frame's end, with a clamping nut 40 above and below: these set the saw's height. Bolt two flange bearings 42 across the frame and fit a 30 mm arbor 43 turned with a collar, a loose flange and an M20 thread; put the 250 mm blade on one end, centred under the slot, and a V-belt pulley 49 on the other. Bend a sheet steel shield 48 round the lower half of the blade and bolt it to the frame.

Materiały do tego kroku:

Kątownik ze stali miękkiejKątownik ze stali miękkiej1 sztuka
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej2 sztuk
Wkręt dociskowy z końcówką wklęsłąWkręt dociskowy z końcówką wklęsłą4 sztuk
Pręt gwintowanyPręt gwintowany1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna4 sztuk
Łożysko kołnierzoweŁożysko kołnierzowe2 sztuk
Circular Saw Blade SetCircular Saw Blade Set1 sztuka
Koło pasowe do pasa klinowego (profil A)Koło pasowe do pasa klinowego (profil A)1 sztuka
Blacha ze stali miękkiejBlacha ze stali miękkiej1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych10 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Szlifierka kątowaSzlifierka kątowa
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw do gwintowaniaZestaw do gwintowania
Pokrętło do gwintownikówPokrętło do gwintowników
Tokarka do metaluTokarka do metalu
Uchwyt tokarski 3-szczękowyUchwyt tokarski 3-szczękowy
Nóż tokarskiNóż tokarski
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Nożyce do blachyNożyce do blachy
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
Zestaw kluczy imbusowychZestaw kluczy imbusowych
7

Motor frame

Bolt a shorter angle frame 53 inside the saw frame, pivoted on the same rear cross bolt, and bolt the motor 51 under it with a V-belt pulley 50 in line with the arbor's. Hang its free end from a bolt 55 off a sleeve 56 on a rod 57 across the saw frame, with a spring 61 and washer 62 on the bolt above the motor frame and a nut 59 below. Fit the belt 52 and set its tension with the nut. Have the motor wired to a switch at the front.

Materiały do tego kroku:

Kątownik ze stali miękkiejKątownik ze stali miękkiej1 sztuka
Silnik elektrycznySilnik elektryczny1 sztuka
Koło pasowe do pasa klinowego (profil A)Koło pasowe do pasa klinowego (profil A)1 sztuka
Pas klinowy (przekrój A)Pas klinowy (przekrój A)1 sztuka
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Pręt gwintowanyPręt gwintowany1 sztuka
Coil SpringCoil Spring1 sztuka
Podkładka płaskaPodkładka płaska2 sztuk
Nakrętka sześciokątnaNakrętka sześciokątna2 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych6 sztuk
Wyłącznik zasilaniaWyłącznik zasilania1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Zestaw kluczy imbusowychZestaw kluczy imbusowych
8

Fence and first cut

Fix a hardwood fence 63 across the top near its rear end, standing past both sides, held by hook bolts 64 that hook under steel flanges 66 screwed to the gussets, with nuts 67. Set the blade 10 mm above the board's thickness with the stem's nuts. Hold a board against the fence, start the motor and press the pedal: the saw comes back through the board. Let the pedal up and it returns.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt gwintowanyPręt gwintowany1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna2 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Wkręty do drewnaWkręty do drewna8 sztuk

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Kątownik nastawnyKątownik nastawny
Okulary ochronneOkulary ochronne
Ochronniki słuchu (nauszniki, SNR 30 dB)Ochronniki słuchu (nauszniki, SNR 30 dB)
9

Troubleshooting

Carriage saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Harry O. Hall** of Murray, Utah, US 1,930,168, dated 10 October 1933, filed 21 March 1933. He claimed a top with a longitudinal slot, "a traveling carriage mounted beneath said top and movable longitudinally thereof", a saw frame pivoted on one cross bar and hung from the other on a stem with nuts above and below, and a motor frame hung from the saw frame on a bolt with a spring. His top is folded sheet metal on splayed legs; ours is plywood on pine. His balls are confined between the cross bolts and lugs; ours the same, in steel angle. He gives no sizes; every size here is ours.

Materiały

27

Wymagane narzędzia

22

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...