Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down

Henry A. Nevers and Charles Ross of Claremont, New Hampshire, received US 30,686, dated 20 November 1860, for a compact plunge churn on its own stand. A hand wheel on a shaft turns a disk whose crank pin runs in a horizontal slot cut in a wooden gate; the gate slides up and down in grooves in two standards and carries the dash rod, so turning the wheel works the dash evenly up and down. Pull one pin and the dasher comes free. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days

Instrukcje

1

Pin in a slot against a connecting rod

Wczytywanie notatnika Jupyter…
2

A wheel plunging the dash by a connecting rod, four months before

Paff drives his dash rod from a flywheel by a pitman. Nevers and Ross put the crank pin in a slot instead.
3

Read US 30,686

"Motion is communicated to the wheel G, and through the shaft F to the disk H, the pin c on which as it revolves plays in the slot d, in the gate I, by which means the gate is raised and lowered vertically and with it the rod J, and dash K, which agitates the cream as required."
4

Base A, standards C, C' and D, platform E

Glue up a hardwood base A 500 x 460 x 25 mm. Rout an 11 mm groove 11 deep down one face of two hardwood standards C, C' 40 x 40 x 830 mm and screw them upright on the base, grooves facing and their inner faces 320 mm apart, either side of where the churn stands. Screw a standard D 40 x 40 x 575 mm behind the churn, 220 mm from its centre. Screw a platform E 177 x 400 x 20 mm across from two cheek blocks on the backs of C, C' to the top of D, its top 575 mm above the base.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna30 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
5

Bearings a, shaft F, disk H, pin c and wheel G

Screw two hardwood bearing blocks a 30 x 50 x 70 mm on the platform, 85 and 170 mm behind the gate's plane, bored 16.6 mm across 45 mm up. Run a 16 mm stainless shaft F 217 mm long through them, held by a shaft collar. Cut a hardwood disk H 180 mm across and 18 thick, fix it on the shaft's front end 40 mm from the gate's plane, and drive a 10 mm stainless pin c 72 mm long through it 60 mm from the centre so 54 mm stands out toward the gate. Cut a hardwood wheel G 240 mm across and 20 thick, fix it on the shaft's back end, and set a hardwood handle b 100 mm from its centre.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Shaft CollarShaft Collar1 sztuka
ZawleczkaZawleczka2 sztuk
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna8 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
KompasKompas
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Zestaw wkrętakówZestaw wkrętaków
6

Gate I with slot d and tongues e

Glue up a hardwood gate I 320 x 200 x 22 mm and cut a slot d 10.5 mm wide and 132 mm long across it, its middle 100 mm above the gate's foot. Glue hardwood strips 10 x 10 mm along both upright edges as the tongues e. Glue a hardwood block 50 x 50 x 60 mm under the gate's foot, bored 25.6 mm up 51 mm for the dash rod, and bore it 6 mm across for the pin f. Slide the gate down between the standards, its tongues in the grooves, the crank pin in the slot.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
7

Body B, cover L, dash rod J and dash K

Use a 20-litre food-grade bucket as the body B, standing between the standards. Cut a 12 mm HDPE cover L to its top, 304 mm across, with a 27 mm hole in the middle, saw it in two halves through the hole and screw a hardwood knob g on each. Cut a 220 mm HDPE disk as the dash K and screw it to the foot of a 25 mm hardwood dash rod J 378 mm long. Put the dash in the bucket, the cover halves round the rod, push the rod up into the gate's block and pin it with a 6 mm stainless pin f.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Płyta HDPEPłyta HDPE1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Wkręty do drewnaWkręty do drewna6 sztuk

Potrzebne narzędzia:

KompasKompas
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Piła do metaluPiła do metalu
Zestaw wkrętakówZestaw wkrętaków
8

The build in 3D

FreeCAD model of this build, the bucket cut open: the base, the grooved standards and the gate with its slot and tongues, the platform with its bearings, the shaft, disk and crank pin, the wheel and handle, the dash rod and dash.
Plik projektowyBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket before fitting the cover. Turn the wheel steadily by its handle, timing it. When the butter comes, lift off the cover halves, pull the pin f, lift out the dash, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka10 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
10

Troubleshooting

Slotted-gate churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry A. Nevers** and **Charles Ross** of Claremont, Sullivan County, New Hampshire, US 30,686, 20 November 1860, "Churn". They claimed "the combined arrangement of the driving shaft F, face plate and crank pin H, c, with the vertically reciprocating carriage I, provided with a horizontal slot d, and the rod J, of the dasher". Their wheel was spoked and their gate's top scalloped; ours are plain wooden discs and a plain gate, and our churn body is a bucket. The patent gives no sizes; every size here is ours.

Materiały

12

Wymagane narzędzia

17

Pliki projektowe

1

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...