Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
Forge

Autor

Forge

13. listopad 2026NO
5
0
0
0
0

Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)

Michael Pemmerl of Chatham, New Jersey, received US 2,518,059, dated 8 August 1950, for an industrial mallet with heads that change. A threaded stud stands out of each end of the steel head, and percussion members of different hardness screw on. A soft member is moulded round a hard ferrule with flanges and a threaded bore, so it cannot pull off. A steel cup holds its inner end from bulging. A thick rubber washer between cup and head stops it working loose and soaks up the shock before it reaches the hand. We make two rubber members from rubber sheet bonded round a flanged nut. The sizes are ours.
Średniozaawansowany
About 2 days

Instrukcje

1

Building a rubber member round its ferrule

Wczytywanie notatnika Jupyter…
2

Read US 2,518,059

"The frictional and cushioning washers 16 and 23, as interposed between the respective percussion members 14 and 17 and the mallet head 10, serve the two-fold purpose of setting up a strong frictional resistance against tendency of said percussion members to accidentally loosen or turn off the coupling studs 13 when the mallet is in use, while at the same time said washers act as impact shock absorbing means."
3

Turn the head 10

From 35 mm steel round bar turn a head 90 mm long between its end faces, and at each end a stud 13 12 mm across and 20 mm long; cut an M12 thread on each with the die. Drill a 20 mm eye through the middle, square to the axis, in a V-block, for the handle.

Materiały do tego kroku:

Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Olej do cięciaOlej do cięcia1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Uchwyt tokarski 3-szczękowyUchwyt tokarski 3-szczękowy
Nóż tokarskiNóż tokarski
Przecinak tokarskiPrzecinak tokarski
Zestaw do gwintowaniaZestaw do gwintowania
Oprawka do narzynekOprawka do narzynek
Imadło warsztatoweImadło warsztatowe
Wiertarka stołowaWiertarka stołowa
Pryzma traserskaPryzma traserska
Zestaw wiertełZestaw wierteł
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Okulary ochronneOkulary ochronne
4

Ferrules 18 and cups 21-22

For each member, saw an M12 coupling nut to 30 mm and lock a 24 mm washer on it 4 mm from each end with a nut and thread locker: the flanges 19 round the threaded bore 20. Turn two cups from 45 mm bar: a base 3 mm thick with a 13 mm hole, and a skirt 12 mm deep bored 40.5 mm to embrace the member's inner end.

Materiały do tego kroku:

Nakrętka sześciokątnaNakrętka sześciokątna6 sztuk
Podkładka płaskaPodkładka płaska4 sztuk
Klej do zabezpieczania gwintówKlej do zabezpieczania gwintów1 sztuka
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
Tokarka do metaluTokarka do metalu
Uchwyt tokarski 3-szczękowyUchwyt tokarski 3-szczękowy
Nóż tokarskiNóż tokarski
WytaczadłoWytaczadło
Przecinak tokarskiPrzecinak tokarski
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
5

Build the rubber members 17

Scribe and cut 4 mm rubber discs 40 mm across with the knife: for each member, seven holed to the ferrule (24 mm holes level with the two flanges and 22 mm round the nut, so the discs either side trap each flange's rim) and five solid discs for the striking face. Brush contact cement on both faces, let it go touch-dry, and build the member up over its ferrule, the ferrule's end flush with the member's inner end; press it in clamps overnight and trim it round.

Materiały do tego kroku:

Płyta z kauczuku naturalnegoPłyta z kauczuku naturalnego1 sztuka
Klej kontaktowyKlej kontaktowy1 sztuka

Potrzebne narzędzia:

KompasKompas
Nóż introligatorskiNóż introligatorski
Ścisk stolarski listwowyŚcisk stolarski listwowy
6

Handle and assembly

Turn an ash handle 300 mm long, fit it in the eye with a glued wedge. Cut two 6 mm rubber washers 23, 40 mm across with 13 mm holes. On each stud put a rubber washer, then a cup, skirt outwards, then screw a member on until its end is in the cup and the washer is squeezed; it should take a firm twist to undo.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Płyta z kauczuku naturalnegoPłyta z kauczuku naturalnego1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Zestaw dłut tokarskich (HSS)Zestaw dłut tokarskich (HSS)
Piła do metaluPiła do metalu
Młotek ślusarski z kulistym rąbemMłotek ślusarski z kulistym rąbem
Nóż introligatorskiNóż introligatorski
7

Troubleshooting

Interchangeable-head mallet troubleshooting.

Flow

Loading...
8

History and honest limits

**Michael Pemmerl** of Chatham, New Jersey, US 2,518,059, dated 8 August 1950, filed 31 October 1947. He claimed a mallet head with a screw-threaded coupling stud at an end, "a percussion member made of relatively soft material such as lead, an internally screw-threaded ferrule made of hard metal imbedded in said percussion member, said ferrule having external annular flanges", "a perforate cupped reenforcing member", and "a perforate rubber washer of substantial thickness" between cup and head. His soft members were moulded, and he names rubber among their materials; ours are rubber discs bonded round the ferrule. He also shows hard metal and rawhide members. He gives no sizes; every size here is ours.

Materiały

9

Wymagane narzędzia

21

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...