Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)
Forge

Autor

Forge

13. listopad 2026NO
7
0
0
0
0

Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)

Spencer C. Rees of Pickens, South Carolina, received US 3,466,973, dated 16 September 1969, for The Singer Company. A rack screwed to the motor housing is moved by a pinion through a window in a box on the base. The pinion is a hollow shaft running in one bore through the box's two side lugs, with a knob at each end. One knob turns it. The other, a zero-set knob with graduations, slips on its sleeve against an O-ring, so it can be set to zero with the bit touching the work. One screw through the middle holds it all together. Only the pinion shaft was metal; the rest was moulded. We print every part in PETG round a small DC motor. The sizes are ours.
Zaawansowany
About 3 days

Instrukcje

1

What one turn of the knob does

Wczytywanie notatnika Jupyter…
2

Read US 3,466,973

"The zero-set knob 40 has a reduced diameter portion 51 which carries circumferentially-spaced graduation marks 52 on its surface." "In the above-described structure it will be noted that the only metallic part required is the pinion shaft 37 which is a relatively simple two-diameter piece."
3

Print the base

The base 10: the split ring with clamp lugs, the box 28 for the rack with its two lugs 50 and stepped bore 33, the window 36, two legs 11 down to the plate 12 with its aperture, and two handle arms. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
Plik projektowySTLCC0 - Free
4

Print the motor housing

The housing 19: a tube for a 42 mm motor, 56 mm outside, a ledge with an 18 mm hole and two M4 holes, and two M3 holes for the rack. Print it ledge down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
Plik projektowySTLCC0 - Free
5

Print the small parts

One plate: the rack 29 (module 1.5), the hollow pinion shaft 37 with its toothed (splined) part, bearing part and end ribs, the adjusting knob 38 with grooves, the flanged sleeve 39, the zero-set knob 40 with 20 graduations and an O-ring groove, and the cover plate 53 with its window 55 and mark 56. PETG, 0.2 mm layers, 40 % infill, 5 walls.
Plik projektowySTLCC0 - Free
6

Motor in the housing

Fit the collet adapter on the motor's shaft, stand the motor in the housing on its ledge and screw it down with two M4 screws; wire it through a toggle switch to the DC supply. Screw the rack to the housing's front with two M3 screws.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka
Silnik elektrycznySilnik elektryczny1 sztuka
Adapter tulejki zaciskowej na wałek silnikaAdapter tulejki zaciskowej na wałek silnika1 sztuka
Śruba z łbem walcowym na imbusŚruba z łbem walcowym na imbus2 sztuk
Śruby maszynoweŚruby maszynowe2 sztuk
Przełącznik dźwigniowyPrzełącznik dźwigniowy1 sztuka
Przewód montażowyPrzewód montażowy1 sztuka
Koszulka termokurczliwaKoszulka termokurczliwa1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Zasilacz prądu stałegoZasilacz prądu stałego
Lutownica elektrycznaLutownica elektryczna
Zestaw kluczy imbusowychZestaw kluczy imbusowych
Zestaw wkrętakówZestaw wkrętaków
GradownikGradownik
7

Base and handles

Turn two hardwood handles 17 and bolt one to each arm with an M8 bolt. Slide the housing into the base with the rack in the box's channel, and put an M5 screw with a wing nut through the clamp lugs.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych2 sztuk
Nakrętka sześciokątnaNakrętka sześciokątna3 sztuk
Śruba z łbem walcowym na imbusŚruba z łbem walcowym na imbus1 sztuka
Nakrętka skrzydełkowaNakrętka skrzydełkowa1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
8

Pinion, knobs and cover

Push the pinion shaft through the box's bore from the right, its toothed part through the window meshing with the rack, its bearing part in the right lug. Fit the O-ring in the zero-set knob's groove, push the sleeve into the knob, and slide them onto the shaft's toothed end from the left, the sleeve in the left lug. Fit the adjusting knob on the right end, its grooves on the shaft's ribs. Pass a long M4 screw through knob, shaft and sleeve with a washer, into a nut in the sleeve, and tighten it until the knobs have only a little end play. Screw the cover over the box with two M3 screws.

Materiały do tego kroku:

O-ringO-ring1 sztuka
Śruba z łbem walcowym na imbusŚruba z łbem walcowym na imbus1 sztuka
Podkładka płaskaPodkładka płaska1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna1 sztuka
Śruby maszynoweŚruby maszynowe2 sztuk

Potrzebne narzędzia:

Zestaw kluczy imbusowychZestaw kluczy imbusowych
Zestaw wkrętakówZestaw wkrętaków
9

Set zero and rout

Fit a bit. Loosen the clamp, turn the adjusting knob until the bit's tip touches the work, then turn the zero-set knob alone until its zero lines up with the cover's mark. Turn the adjusting knob to the depth wanted, read off the graduations, and clamp. Rout with both hands on the handles.

Potrzebne narzędzia:

Zestaw frezów do frezarkiZestaw frezów do frezarki
Deska z drewna liściastegoDeska z drewna liściastego
Ścisk stolarski listwowyŚcisk stolarski listwowy
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Okulary ochronneOkulary ochronne
10

Troubleshooting

Rack and pinion router troubleshooting.

Flow

Loading...
11

History and honest limits

**Spencer C. Rees** of Pickens, South Carolina, assignor to The Singer Company, US 3,466,973, dated 16 September 1969, filed 8 January 1968. He claimed a rack on the motor housing, "a pair of lugs formed on the base in fixed spaced relation on opposite sides of the rack and having aligned cylindrical apertures", a hollow pinion shaft, an adjusting knob, a flanged sleeve, "a zero-set knob frictionally coupled to said sleeve", and "single fastening means" through them all. His pinion shaft was metal and the rest moulded; ours is all printed. His motor ran on mains; ours is a small DC motor. He gives no sizes; every size here is ours.

Materiały

14

Wymagane narzędzia

15

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...