Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
Forge

Autor

Forge

13. listopad 2026NO
7
0
0
0
0

Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)

Homer E. Willard and Frederick S. Young of Toledo, Ohio, received US 2,146,458, dated 7 February 1939, for a simple portable router with few moving parts. The motor sits in an open-fronted support in the middle of a T-shaped frame, so the bit and the work are always in view. The frame stands on three legs on the table beside the clamped work: two curved legs at one end, and at the other a screw with a knob. Turning the knob with one hand raises or lowers the bit while it cuts. We print the frame in PETG round a small DC motor. The sizes are ours.
Średniozaawansowany
About 1 day

Instrukcje

1

Depth by the knob

Wczytywanie notatnika Jupyter…
2

Read US 2,146,458

"Thus, by turning the wrist in one direction or the other, the bit 19 may be raised or lowered, as required, without stopping the motor and without removing the hands from the tool."
3

Print the frame

The T-shaped frame 10: the motor support 13 with its ledge 14 (an 18 mm hole and two M4 holes 29 mm apart) and curved wall 15, open at the front 16; arm 11 to the cross with two curved legs 21, 22; arm 12 to a boss with an M10 nut trap for the screw leg 24. PETG, 0.2 mm layers, 40 % infill, 5 walls; print it legs up, ledge on the bed.
Plik projektowySTLCC0 - Free
4

Fit the motor

Print the frame. Fit the collet adapter on the motor's shaft, stand the motor in the support with its face on the ledge and the collet through the hole, and screw it down with two M4 screws. Wire it through a toggle switch to the DC supply as for our 1924 router.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka
Silnik elektrycznySilnik elektryczny1 sztuka
Adapter tulejki zaciskowej na wałek silnikaAdapter tulejki zaciskowej na wałek silnika1 sztuka
Śruba z łbem walcowym na imbusŚruba z łbem walcowym na imbus2 sztuk
Przełącznik dźwigniowyPrzełącznik dźwigniowy1 sztuka
Przewód montażowyPrzewód montażowy1 sztuka
Koszulka termokurczliwaKoszulka termokurczliwa1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Zasilacz prądu stałegoZasilacz prądu stałego
Lutownica elektrycznaLutownica elektryczna
Zestaw kluczy imbusowychZestaw kluczy imbusowych
5

The screw leg and knob

Press an M10 nut into the trap under the boss. Cut 100 mm of M10 threaded rod, round its lower end with a file so it slides on the table, and screw it up through the nut. Turn a hardwood knob 25, bore it, and glue it on the rod's top with a nut locked under it.

Materiały do tego kroku:

Nakrętka sześciokątnaNakrętka sześciokątna2 sztuk
Pręt gwintowanyPręt gwintowany1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Zestaw pilnikówZestaw pilników
Tokarka do drewnaTokarka do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
6

Rout

Clamp the work down on the table between two strips. Fit a bit and stand the router on the table so its legs are beside the work and the bit is over it. Turn the knob until the bit just clears the work, switch on, and turn it down a little while moving the router over the area to be cut, one hand on arm 11 and the other on the knob.

Potrzebne narzędzia:

Zestaw frezów do frezarkiZestaw frezów do frezarki
Deska z drewna liściastegoDeska z drewna liściastego
Ścisk stolarski listwowyŚcisk stolarski listwowy
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Okulary ochronneOkulary ochronne
7

Troubleshooting

Three-legged router troubleshooting.

Flow

Loading...
8

History and honest limits

**Homer E. Willard** and **Frederick S. Young** of Toledo, Ohio, US 2,146,458, dated 7 February 1939, filed 11 December 1935. They claimed "a portable router comprising a T-shaped frame having a semi-circular recess in the stem of the T, a bit-operating motor mounted in said recess and a leg projecting in the same direction as the bit from each of the ends of the frame", one leg "screw-threaded through the arm and terminating above the arm in an operating knob". Their work was an electrotype clamped on the table; their motor ran on mains. Ours is a small DC motor in a printed frame. They give no sizes; every size here is ours.

Materiały

11

Wymagane narzędzia

15

Pliki projektowe

1

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...