Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
James Sangster of Buffalo, New York, received US 27,570, dated 20 March 1860, for a churn. A false bottom divides the churn; paddles spinning beneath it draw the cream and air down through holes near its centre and throw it up through holes near its rim, under caps that aim the streams against each other. Another paddle turns above. The cream goes round and round, from rim to centre and back.
The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing
Instrukcje
1
1
Down at the centre, up at the rim
Down at the centre, up at the rim
Wczytywanie notatnika Jupyter…
2
2
An upright churn with a pierced cover, one week before
An upright churn with a pierced cover, one week before
Wiswell's cover is above the scoops. Sangster's pierced partition is below the cream, with paddles under it.
3
3
Read US 27,570
Read US 27,570
"U and V represent caps which partially cover the apertures L and N. They are placed in such a position as to cause the fluid to flow in streams against each other, by boring the holes L and N at the same angles at which the caps U and V are set. The caps may be dispensed with and the same result obtained."
4
4
Print the caps Q, U, W, V
Print the caps Q, U, W, V
Hood cap 50 mm across, open on one side. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the crown wheel
Print the crown wheel
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Rim Y and partition E
Rim Y and partition E
Screw a ring of HDPE strip 10 mm thick and 12 high inside the bucket with its top 60 mm above the floor, as the rim Y, sealing the screw holes outside with silicone. Cut a disc of 10 mm HDPE sheet to rest on it, bored 17 mm in the centre. Bore four 30 mm holes, H, I, J, K, 45 mm from the centre, a quarter turn apart, and four 25 mm holes, L, M, N, O, 112 mm from the centre between them, each bored at 45 degrees slanting toward the centre as it rises. Screw a printed cap over each rim hole, its open side toward the centre.
Materiały do tego kroku:
Wiadro 20-litrowe1 sztuka
Płyta HDPE1 sztuka
Śruby maszynowe16 sztukPotrzebne narzędzia:
Wyrzynarka
Zestaw otwornic
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Kątomierz
Pilniki (pilnik ręczny)
Zestaw wkrętaków8
8
Spindle D, paddles C, G and Z, shoulder J'
Spindle D, paddles C, G and Z, shoulder J'
Screw a hardwood block 50 x 50 x 6 mm to the floor's centre and bore it 17 mm, 5 deep, as the step. Cut a 16 mm stainless spindle 435 mm long and turn or file its top 75 mm down to 12 mm. Fix a hardwood paddle bar 250 x 45 x 20 mm across it, 8 mm above the floor when the spindle stands in its step (the paddles C and G), pass it up through the partition, and fit a printed or hardwood collar 32 mm across and 20 high on it just above the partition as the shoulder J'. Fix a second paddle Z, 200 x 30 x 20 mm, across it 185 mm above the floor.
Materiały do tego kroku:
Pręt ze stali nierdzewnej1 sztuka
Deska z drewna liściastego1 sztuka
Klocek z drewna twardego1 sztuka
Klej do drewna1 sztuka
Wkręty do drewna2 sztuk
Shaft Collar2 sztuk
Zawleczka2 sztukPotrzebne narzędzia:
Piła do metalu
Pilniki (pilnik ręczny)
Imadło warsztatowe
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Pilarka stołowa
Papier ścierny
Zestaw wkrętaków9
9
Top I' and crank X
Top I' and crank X
Cut a hardwood top 350 x 205 x 25 mm to sit on the bucket's rim and bore it 13 mm over the centre for the spindle; fit the pinion on the spindle above it. Screw two hardwood chairs on the top carrying a 12 mm stainless crank shaft with the crown wheel meshing the pinion, and fit a hardwood crank X with a dowel handle on its end.
Materiały do tego kroku:
Deska z drewna liściastego2 sztuk
Pręt ze stali nierdzewnej1 sztuka
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztuka
Wkręty do drewna8 sztuk
Shaft Collar2 sztuk
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Pilarka stołowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Piła do metalu
Ścisk stolarski listwowy
Zestaw wkrętaków
Miara zwijana10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut through the middle: the paddles C and G under the partition E on its rim Y, the centre and rim holes with their caps, the shoulder J', the paddle Z, and the top with the crank, crown wheel and pinion.
11
11
Churn
Churn
Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket over the partition, set the top and gearing on the rim, and turn the crank steadily, timing it. When the butter comes, lift off the top, lift out the spindle and partition, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka8 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej12
12
Troubleshooting
Troubleshooting
False-bottom churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**James Sangster** of Buffalo, New York, US 27,570, 20 March 1860, "Churn". He claimed the paddles Z, C and G with the partition E pierced near its centre and near its rim under caps, "for the purpose of passing the cream around and around through the openings from circumference to center and vice versa". He made it of "wood, tin or any other suitable material"; ours is a food-grade bucket with an HDPE partition and printed caps and gears. Every size here is ours.
Materiały
16- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 16 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 10 sztukZastępnik
- 2 sztukZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
19- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
4Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Leaning-Scoop Churn: Three Scoops Tilted 10, 5 and 0 Degrees Throw the Cream at Sharp-Topped Ribs and a Slit Cover
autor: Buttercup
Obróbka drewna
8
0
0
0
0
0

Counter-Revolving Dasher Churn: Geared Dashers on Offset Shafts Turn Contrary Ways, Their Blades Skewed Contrary Ways
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

