Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)
Forge

Autor

Forge

15. listopad 2026NO
4
0
0
0
0

Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)

The crushing rolls that took ore from the jaw breaker in a 1900s mill, as Robert Richards described them: two shafts on one cast-iron frame, each carrying a soft-iron core with a replaceable hard shell; one runs in fixed boxes, the other in movable boxes pushed toward it by a nest of steel springs that yields like a safety valve; shims set the gap. Little fines, ideal for soft brittle ores.
Zaawansowany
Weeks (castings and machining)

Instrukcje

1

His figures

Wczytywanie notatnika Jupyter…
2

Read Richards

"The ore is therefore broken by compression."
3

Frame and shafts

Cast the frame as one piece, both sides joined by end pieces, so settling of the building can't throw the shafts out of line (make it in two parts only if it must travel by mule). Turn two shafts of mild steel or wrought iron, each on two bearings.

Materiały do tego kroku:

Odlewy żeliwneOdlewy żeliwne1 sztuka
Wał stalowyWał stalowy1 sztuka

Potrzebne narzędzia:

Kadź odlewniczaKadź odlewnicza
Tokarka do metaluTokarka do metalu
WielokrążekWielokrążek
4

Cores and shells

Force a soft cast-iron core onto each shaft. Krom's way (Fig. 37): two slightly conical half-cores, one shrunk on for good, the other split on one side and drawn in by four draw bolts; half-cores no wider than 4-5 in. Cast hard shells 2-5½ in. thick (chilled iron or steel), with wrought-iron staves cast in if chilled so the slightly conical inside can be turned to fit; turn the face true.

Materiały do tego kroku:

Odlewy żeliwneOdlewy żeliwne1 sztuka
Pręt z kutego żelazaPręt z kutego żelaza1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Kadź odlewniczaKadź odlewnicza
5

Boxes, springs and shims

Mount one shaft in fixed boxes and the other in movable ones, both babbitted, with shields and a cotton-waste groove against grit. Put a nest of steel spiral springs outside the fixed pillow block, with bolts carrying the force to the movable box, equal on both sides, compressed between plates by two compression bolts. Set the gap with shims and keep them in: the springs should only give when a hard lump comes through.

Materiały do tego kroku:

Coil SpringCoil Spring1 sztuka
Nieznany metalNieznany metal1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka
Odlewy żeliwneOdlewy żeliwne1 sztuka

Potrzebne narzędzia:

Zestaw kluczy płaskichZestaw kluczy płaskich
Tokarka do metaluTokarka do metalu
6

Drive and run

Drive by belt and pulley (or gears and pulleys for slow coarse work). Feed lumps no bigger than about 1½ in. (4 cm), 2½ in. at most, evenly with a feeder so a rush of ore does not choke it.

Materiały do tego kroku:

KrążekKrążek1 sztuka
Pas napędowyPas napędowy1 sztuka

Potrzebne narzędzia:

Zestaw kluczy płaskichZestaw kluczy płaskich
7

Troubleshooting

Crushing rolls troubleshooting.

Flow

Loading...
8

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter III, §§ 71-85, pp. 62-74, Fig. 37 and Tables 34-39 (checked on the archive.org scan oredressing01richuoft; p. 62 from its text layer). Rubber springs were the cheap short-life option; levers and weights had nearly gone out of use. Richards surveys machines from many makers rather than one design: building from castings, the size and metric are ours, and the babbitt alloy has no head yet.

Materiały

8

Wymagane narzędzia

4

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...