Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
Forge

Autor

Forge

13. listopad 2026NO
6
0
0
0
0

Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)

William A. Tomlinson and Howell B. Bearden of Phoenix, Arizona, received US 1,813,783, dated 7 July 1931, for a table that turns any portable power saw into a table saw. The saw is clamped upside down on a carriage, its blade through the slot of a top hinged at the rear. The carriage rolls on ball-bearing rollers inside two steel tubes slotted along their undersides. A pedal pushes it forward through the work, leaving both hands free, and a spring brings it back. With the pedal left alone it works as a fixed saw, and the saw unbolts for hand use. The patent gives no sizes; every size here is ours.
Zaawansowany
About 4 days

Instrukcje

1

Pedal, link and travel

Wczytywanie notatnika Jupyter…
2

Read US 1,813,783

"By using the pedal in the manner above set forth both hands of the operator will be free for manipulating the work, which is especially desirable when pattern work is to be sawed."
3

Angle-iron frame

Bolt a frame of steel angle 900 x 500 mm, 850 high: four corner legs 1, side and end bars 2, 3 halfway up and 4, 5 at the top, flat-bar diagonal braces 6 at the top corners, a cross bar 7 between the rear legs above the middle bars, and a cross bar 8 between the front legs at the bottom. Drill a vertical row of 9 mm holes 13, 25 mm apart, near the top of each leg, for the track hangers.

Materiały do tego kroku:

Kątownik ze stali miękkiejKątownik ze stali miękkiej6 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych40 sztuk
Nakrętka sześciokątnaNakrętka sześciokątna40 sztuk
Podkładka płaskaPodkładka płaska40 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Szlifierka kątowaSzlifierka kątowa
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
PunktakPunktak
Kątownik nastawnyKątownik nastawny
Miara zwijanaMiara zwijana
Klucz nastawnyKlucz nastawny
Okulary ochronneOkulary ochronne
4

Slotted tube tracks

Cut two 900 mm lengths of 42 mm steel tube 9, 10 and cut a 10 mm slot 14 along the underside of each, stopping 20 mm short of the ends; file the slot's edges smooth. Bolt a flat-bar hanger 11 to each end of each tube and hang the tubes along the frame's sides from the legs with bolts 12 through the row of holes, at the height that suits your saw. Put a short coil spring 39 in each end of each tube as a buffer.

Materiały do tego kroku:

Rura okrągła ze stali miękkiejRura okrągła ze stali miękkiej2 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Coil SpringCoil Spring4 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych8 sztuk
Nakrętka sześciokątnaNakrętka sześciokątna8 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Szlifierka kątowaSzlifierka kątowa
Zestaw pilnikówZestaw pilników
Imadło warsztatoweImadło warsztatowe
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Okulary ochronneOkulary ochronne
5

Carriage and rollers

Cut the carriage 30 from 5 mm steel plate, as wide as between the tubes. At each corner bolt an upright flat-bar standard 31 that reaches up through a tube's slot, and on its top a short bar 33 across inside the tube carrying a 22 mm ball bearing 32 at each end on an M8 bolt with a lock nut. Slide the rollers into the tubes from the ends, the standards hanging down through the slots, and bolt them to the carriage.

Materiały do tego kroku:

Blacha gruba ze stali niskowęglowejBlacha gruba ze stali niskowęglowej1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Łożysko kulkoweŁożysko kulkowe8 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych16 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową8 sztuk
Podkładka płaskaPodkładka płaska16 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Szlifierka kątowaSzlifierka kątowa
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw pilnikówZestaw pilników
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
6

Pedal and springs

Pivot a lever 21 of steel flat bar on the front bottom cross bar 8, with an arm 22 to the side carrying the pedal 20 and a brace 23 from arm to lever. Join the lever's top to the carriage's front with a flat-bar link 24. Hook a return spring 25a from the rear cross bar 7 to the lever partway up.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej2 sztuk
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Sprężyna naciągowaSprężyna naciągowa1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
7

Mount the saw and the top

Turn the circular saw upside down on the carriage and bolt it by its base plate with bolts and wing nuts, so it lifts off for hand use; his T-bolt 34 and hook bolts 36 gripped the saw's handles, which modern saws do not suit. Make the top 42 of plywood on a steel angle frame 44, slotted along the blade's path, and hinge its rear edge to the frame so it swings up to reach the saw. Fit a catch 47 to lock it down and a folding flat-bar brace 49 to prop it up.

Materiały do tego kroku:

Pilarka tarczowaPilarka tarczowa1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych4 sztuk
Nakrętka skrzydełkowaNakrętka skrzydełkowa4 sztuk
Płyta sklejkowaPłyta sklejkowa1 sztuka
Kątownik ze stali miękkiejKątownik ze stali miękkiej1 sztuka
Zawias czopowyZawias czopowy2 sztuk
HaftkaHaftka1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Wkręty do drewnaWkręty do drewna16 sztuk

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Klucz nastawnyKlucz nastawny
Kątownik nastawnyKątownik nastawny
8

Cut

Lock the top down. Set the saw's depth so the blade stands 10 mm above the board. Place the board on the top in front of the blade, start the saw and press the pedal: the carriage rolls the running blade through it while both hands hold the work. Let the pedal up and the spring returns it. For ripping, leave the carriage still and feed the board.

Potrzebne narzędzia:

Okulary ochronneOkulary ochronne
Ochronniki słuchu (nauszniki, SNR 30 dB)Ochronniki słuchu (nauszniki, SNR 30 dB)
9

Troubleshooting

Tube-track saw table troubleshooting.

Flow

Loading...
10

History and honest limits

**William A. Tomlinson** and **Howell B. Bearden** of Phoenix, Arizona, US 1,813,783, dated 7 July 1931, filed 5 December 1928. They claimed a top with a slot, "laterally spaced longitudinally extending tubular tracks" below it, "slotted longitudinally on their lower faces", and a saw carriage with upstanding roller-carrying hangers in the tracks, their shanks through the slots. Their saw is held by its handles; ours by its base plate. Their frame is angle iron, as ours. They give no sizes; every size here is ours.

Materiały

18

Wymagane narzędzia

15

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...