Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Spiral-Flange Perforated Dasher Churn: Curved Holed Dashers Fling the Cream Out, a Spiral Flange With Vanes Drives It Back Down
John J. Watson of Buffalo, New York, received US 30,438, dated 16 October 1860, for a churn dasher turned by a crank on its staff. Curved main dashers with turned, perforated ends catch the cream as it flies outward, part through their holes and part along the curve back toward the staff, rising; a spiral flange round the staff, with small unperforated vanes, catches that rising cream and throws it back down to the main dashers.
The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days
Instrukcje
1
1
Flinging out, falling back
Flinging out, falling back
Wczytywanie notatnika Jupyter…
2
2
Perforated dashers that break the cream, ten months before
Perforated dashers that break the cream, ten months before
Sprinkle's perforated dasher is driven at a slant. Watson curves and turns the ends of his and adds a spiral flange to send the cream back down.
3
3
Read US 30,438
Read US 30,438
"Around the dasher staff is wound a spiral flange, E, upon which are formed auxiliary dashers, a, a. These dashers are not perforated but catch the cream as it approaches the shaft with an upward tendency and throw it back toward the bottom of the churn box or toward the large or main dashers below them."
4
4
Box A and lid
Box A and lid
Use a 20-litre food-grade bucket as the box A. Cut a 12 mm HDPE lid to its top, 304 mm across, bored 16.6 mm at the centre as the staff's top bearing.
Materiały do tego kroku:
Wiadro 20-litrowe1 sztuka
Płyta HDPE1 sztukaPotrzebne narzędzia:
Kompas
Wyrzynarka
Zestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowa5
5
Print the step
Print the step
The step on the bucket's floor: 60 mm across, 10 high, with a 10.6 mm hole 9 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Print the main dashers D (six)
Print the main dashers D (six)
One main dasher D: a blade 60 mm high and 4 thick, straight from the hub then curved forward over its outer 40 mm to 120 mm from the staff's centre, with 8 mm holes in two rows along the curve, on an 18 mm hub with a 10.4 mm bore and a split-pin hole. Print six. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Print the spiral flange sections E (two)
Print the spiral flange sections E (two)
One section of the spiral flange E: a third of a turn of 120 mm pitch, reaching from a 38 mm sleeve (32.4 mm bore, 40 high) to 55 mm out, 4 thick, with three vanes a 10 mm high leaning 30 degrees. Print two, with supports. PETG, 0.2 mm layers, 30 % infill, 4 walls.
8
8
Staff B, flange E and dashers D
Staff B, flange E and dashers D
Turn a hardwood staff B 32 mm across and 315 mm long. Set a 10 mm stainless pin 10 mm out of its foot and a 16 mm stainless rod 133 mm long 20 mm into its top. Slide the two flange sections on, one 80 to 120 mm above the foot and one 190 to 230 mm, the upper turned a quarter turn on from the lower, and fix each with a screw through its sleeve. Bore the staff 10.2 mm across at 45, 155 and 265 mm above its foot, each a quarter turn from the last, and push a 10 mm stainless rod 120 mm long through each. Slide a dasher D on each end, curves leading the same way round, and fix it with a split pin. Pin a crank of mild steel flat bar, 108 mm throw, with a hardwood handle on the stainless top.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnej3 sztuk
Filament PETG1 sztuka
Wkręty do drewna2 sztuk
Zawleczka6 sztuk
Płaskownik ze stali miękkiej1 sztuka
Kołki z twardego drewna1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Tokarka do drewna
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Piła do metalu
Pilniki (pilnik ręczny)
Imadło warsztatowe
Zestaw wkrętaków
Miara zwijana9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the step, the staff with its three pairs of curved, holed dashers on cross-rods, the two spiral flange sections with their vanes between the levels, the lid and the crank.
10
10
Churn
Churn
Set the step on the bucket's floor, stand the dasher in it, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and put on the lid over the staff's top. Turn the crank steadily, the dashers' curved ends leading, timing it. When the butter comes, lift the lid and dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka12 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej11
11
Troubleshooting
Troubleshooting
Spiral-flange churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**John J. Watson** of Buffalo, Erie County, New York, US 30,438, 16 October 1860, "Churn-Dasher". He claimed "the arrangement of the main dashers, D, D, with the auxiliary dashers, a a and the spiral flange E". He gives the dashers' form only as drawn, and does not say how many there are or how far round the flange runs; Fig. 1 draws one twisted band up the staff's height, while ours is two short sections between the dashers' levels. His dashers were metal; ours are printed. Every size here is ours.
Materiały
12- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 3 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 6 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
16- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
4Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Oblique Perforated-Dasher Churn: A Slanted Spindle Drives the Cream Down and Sideways, a Guard Turns It Back
autor: Buttercup
JEDZENIE I NAPOJE
9
0
0
0
0
0

Interlapping Spiral-Dasher Churn: Two Upright Shafts With Arms Set in Screw Form Interlap, One Turning the Other
autor: Buttercup
Obróbka drewna
4
0
0
0
0
0

Centrifugal-Dasher Churn: Curved Wings on a Hollow Shaft Throw the Cream at the Wall, a Fixed Disk Turns It Back
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

