Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Interlapping Spiral-Dasher Churn: Two Upright Shafts With Arms Set in Screw Form Interlap, One Turning the Other
D. M. Woodin of Brandon, Wisconsin, received US 28,528, dated 29 May 1860, for a churn. Two shafts stand side by side in a box, each with arms set round it in a screw form; the arms of one pass between the arms of the other, so turning one shaft with the crank turns the second "like spiral gearing". The two screws force the cream down between them and it rises again outside, while the arms meet and close on each other, breaking the globules.
The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing
Instrukcje
1
1
Where the shafts go
Where the shafts go
Wczytywanie notatnika Jupyter…
2
2
Two dashers turning contrary ways, three months before
Two dashers turning contrary ways, three months before
Vaughan joins his two dashers with pinions. Woodin lets the dashers' own arms drive one another.
3
3
Read US 28,528
Read US 28,528
"These two spiral wheels revolving in this way force the cream downward all the while, but it rising again on the outside of the wheels, is kept moving in a constant current from top to bottom, and from bottom to top. In addition to the friction thus caused and the moving of the cream in a constant current, the arms overlapping and interlapping mash the globules of the cream as they meet and press against each other."
4
4
Print the crown wheel
Print the crown wheel
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Box A and steps
Box A and steps
From 20 mm hardwood board make a box 350 x 220 mm inside and 350 deep; glue and screw it and seal the inside joints with silicone sealant. Screw two hardwood blocks 50 x 50 x 10 mm to the floor on the long centre line, 128 mm apart, the first 110 mm from one end, each bored 16.6 mm, 6 deep, as steps. Cut a lid to sit on top, bored 17 mm over each step.
Materiały do tego kroku:
Deska z drewna liściastego3 sztuk
Klocek z drewna twardego2 sztuk
Klej do drewna1 sztuka
Wkręty do drewna40 sztukPotrzebne narzędzia:
Pilarka stołowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Ścisk stolarski listwowy
Zestaw wkrętaków
Miara zwijana7
7
Wheels B, B with spiral arms a
Wheels B, B with spiral arms a
For each wheel cut fourteen hardwood bars 190 x 30 x 20 mm and halve them together in pairs into seven crosses, each bored 16.2 mm at the crossing. Thread the crosses onto a 16 mm stainless shaft, 40 mm apart centre to centre from 40 mm above the floor, each turned 22.5 degrees from the one below, checked with the protractor, and pin each through. Turn the second wheel's crosses the opposite way, so its spiral is of the other hand. The driven shaft is 425 mm long, the other 375.
Materiały do tego kroku:
Deska z drewna liściastego2 sztuk
Pręt ze stali nierdzewnej2 sztuk
Klej do drewna1 sztuka
Zawleczka14 sztukPotrzebne narzędzia:
Pilarka stołowa
Komplet dłut do drewna
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Piła do metalu
Pilniki (pilnik ręczny)
Kątomierz
Papier ścierny8
8
Set the wheels and the gearing
Set the wheels and the gearing
Stand both shafts in their steps and turn the second so its arms sit 45 degrees between the first's at every level; they must pass each other about 5 mm apart all the way round. Put on the lid. On the driven shaft's top fit the pinion; on the lid screw two hardwood chairs carrying a 12 mm stainless crank shaft with the crown wheel meshing it, and a hardwood crank with a dowel handle. Hold the shafts with collars.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnej1 sztuka
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztuka
Wkręty do drewna8 sztuk
Shaft Collar4 sztuk
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Pilarka stołowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Piła do metalu
Zestaw wkrętaków9
9
The build in 3D
The build in 3D
FreeCAD model of this build, one side left off: the two wheels with their seven crossed stations turned in spirals of opposite hand, their arms interlapping, the steps, the lid and the crank with crown wheel and pinion on the driven shaft.
10
10
Churn
Churn
Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, put the lid and gearing on, and turn the crank steadily, timing it, the way that drives the cream down between the wheels. When the butter comes, lift off the lid and the wheels, take out the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka10 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej11
11
Troubleshooting
Troubleshooting
Interlapping-dasher churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**D. M. Woodin** of Brandon, Fond du Lac County, Wisconsin, US 28,528, 29 May 1860, "Churn". He claimed the two dasher shafts with wings in screw form, one turned by the other. He does not give the number of arms or how far each turns on; our seven stations of four arms, 22.5 degrees apart, and the spacing are ours, as are the printed crown wheel and pinion that stand in for his bevel wheels.
Materiały
13- 3 sztukZastępnik
- 2 sztukZastępnik
- 3 sztukZastępnik
- 48 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 14 sztukZastępnik
- 1 sztukaZastępnik
- 4 sztukZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
17- 1 vendor sell this, none ship to you yetZastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
3Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Counter-Revolving Dasher Churn: Geared Dashers on Offset Shafts Turn Contrary Ways, Their Blades Skewed Contrary Ways
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Nested Hollow-Dasher Churn: Two Dasher Frames Turn Contrary Ways, Their Hollowed Side Pieces Driving Cream at Webs
autor: Buttercup
Obróbka drewna
8
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

